All Forums
Browse the Community
USB
Universal Serial Bus (USB) forums have discussions regarding Low-Full & High Speed Peripherals, Superspeed Peripherals, USB Hosts Hubs Transceivers, and USB EZ-PD Type C product solutions for PCs and consumer device topics.
Wireless Connectivity
Power
Sensors
Memories
Memory Discussion Forums discussions regarding NOR Flash, SRAM, nvSRAM and F-RAM - performance and reliability with discrete memory densities ranging from 4K-bit to 2G-bit topics.
Other Technologies
Discussion forum regarding Other Technologies including Power Management and Clocks topics.
Security & Smart Card
Radio Frequency (RF)
Software
Software including ModusToolbox, PSoC Creator, WICED Studios and Wi-Fi Bluetooth for Linux .
Applications
Featured Discussions
How to interpret the .npy files that we get in the Radar Fusion GUI. I used the np.load to load the contents of the array( image attached below),the shape of the array is correct, but i am not able to understand what the contents are? Is the contents of .npy file the raw ADC data or it is in byte format?
Show Less
Hi~
I'd like to import sameple application named 'Hello Sensor ' from based on CYW20706 to CYBT-343026-01
Because there is no sample applicaion which has same name in CYBT-343026-01
After installing sample application, I tried to exchange BSP from CYW20706 to CYBT-343026-01.
I found some decription indicates successful, But some otheres were not.
Operation is okay after build and flash. But I'm still curious whether it is really okay or not.
Please make me sure it
I attahced error code picture
Many thanks
BRs
Daniel Lim
Show Less
Dear Forum:
We are doing our soft with pSoC6 CY8C6137BZI-F14,
We use the Modus IDE.
But when we use psoc programmer to write Hex file produced by Modus,
psoc programmer show the following error:
Hex File parsing failure. Unknown record type.
Can you tell me the reason.
Thank you.
Show LessHi ,
I am trying to stream video data via FX3 coming from my fpga at 5200*3900 resolution at 15fps and not able to set min /max bit rate descriptor value as descriptor size is only 32 bit.
Desired value of the descriptor should be -
(width x height x data width x frame rate)
5200x3900x16x15 = 0x1221B9400
but this value is more than 32 bits.
how can I go ahead with above mentioned requirements?
Note - I have implemented a design taking AN75779 reference with same resolution but at 5fps and it is working fine now I wish to increase frame rate.
Thanks & Regards,
Akash
Show LessHello,
We are producing radar modules using BGT60UTR11AIP. We have found that the DC-offset of ADC data changes significantly between chips under the same conditions.
Is the DC-offset variation managed during the chip production? Or is there a way to calibrate it to a specific level?
Regards,
YK
Show LessHi.
I'm a student. I have a PCB with the SAK-TC214L-8F133 chip on it. I would like to be able to connect to it using Memtool. I see Memtool supports this layout. I have a USB-UART converter.
How should I connect from the hardware side? Connect TxD from the converter to P14.1 (ASCLIN0_RXA) and RxD to P14.0 (ASCLIN0_TX)? I did that, but Memtool does not detect the chip. Do I need to short any configuration pins to VCC/GND?
I will be grateful for your help.
Good morning everyone, I have a system with Psoc4100S-Plus, VDDA at 5V and VDDD at 3.3V.
The CapSense block is powered by VDDA.
Why is the Tx signal for CSX mode 3.3V?
Can it be set to 5V of VDDA?
Hi,
I recently installed PSoC Creator 4.4 on another PC (shares PSoC projects with the old PC) and I found that the example projects shown in 'Find Code Example' are limited to the examples I already downloaded.
The examples with download icon are not displayed anymore. This problem occurs on the old PC too. First I thought it as a setting problem or something related to corrupted files but I could not find anything about that.
Screenshot shown below.
Searching through the developer community, I found a similar case closed over 3 years ago.
Solved: examples visibility - Infineon Developer Community
If this is the same case, anyone who tries to use code examples should get the same issue with me. Is there anybody having same issue?
Thank you.
Show LessI'm having an issue with 30A TV. I've submitted a video, but it's not showing up on their channel. Does anyone have any advice on what I should do in this situation? I've checked their guidelines and made sure my video meets all the requirements, but it's still not being aired. Any insights or suggestions would be greatly appreciated. Thanks!"
-
TraveoII
UART buadrate Setting
by chandan1995 Jun 19, 2023