Wireless Connectivity Forum Discussions
Browse the Community
AIROC™ Wi-Fi and Wi-Fi Bluetooth Combos
AIROC™ Wi-Fi MCUs
AIROC™ Bluetooth
Featured Discussions
Hi,
We would like to search one WIFI /BT Combo chipset solution for our new project, the details requirement as below, Can you help on check if have suitable solution which can meet the specification, thanks!
Dual Band Wi-Fi: 802.11 a/b/g/n, 2TX x 2RX.
Bluetooth: BLE5.2, 2 Mbps, Long Range.
The chipset shall support "Matter" over Wi-Fi.
BR
Frank.
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AIROC-Wi-Fi%E4%B8%8EWi-Fi-%E8%93%9D%E7%89%99%E7%BB%84%E5%90%88/WIFI-4-802-11n-2x2-BLE-5-2-Combo-chipset-solution/td-p/715777
Show LessHi IFX,
Chip :cyw43455
1.Below setting can connected to AP1(WPA2+802.11r) .
network={
ssid="80211Rtest"
proto=RSN WPA
key_mgmt=SAE FT-PSK WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="12345678"
}
2. disconnected to AP1(WPA2+802.11r)
3.connected to AP2(WPA3) :CYW43455 can not connect to AP2(WPA3).
Is it impossible to connect to AP2(WPA3) after adding FT-PSK in wpa_supplicant.conf ?
If yes, could you give me some guidance about waht wpa_supplicant.conf setting support AP1(WPA2+802.11r) and AP2(WPA3) .
We want the same wpa_supplicant.conf setting for AP1(WPA2+802.11r) and AP2(WPA3) .
B.R.
Bill.
Show LessHello Infineon support team.
Our custmer would like to evaluate BLE mesh using CYBT-213043-MESH kit.
https://www.infineon.com/cms/jp/product/evaluation-boards/cybt-213043-mesh/
However, there is no BSP for CYBT-213043-MESH on project creator in ModusToolBox ver 3.2.
(We can see a BSP for CYBT-213043-EVAL(not CYBT-213043-MESH), but no find reference BLE mesh app.)
How can we find BLE mesh reference application for CYBT-213043-MESH kit?
Thanks,
Tayo
Hi.
I use the CYBT-413061 module (CYW20721B2) on a custom board and try to run the RFCOMM_Serial_Port SPP demo in ModusToolbox 3.2. The code seems to load OK, but when starting the Client Control App and open the serial port, nothing happens - the controls are all greyed out. I then also run BTSpy and connects from a Windows 10 PC as suggested in the instructions - the Client Control App then seems to connect (not greyed out anymore), but nothing happens when pressing any buttons. BTSpy however, seems to display everything, like when hitting a key on Windows/TeraTerm BTSpy, it displays the messages - but nothing shows up on the Client Control App SPP tab or message window.
What could be wrong?
Regards, Roger
Show Lessgetting error
Break at address "0x50dc3e" with no debug information available, or outside of program code. if i debug using OpenOCD and cable used is kitprog3 (provided with the board).
Info : Listening on port 3333 for gdb connections
Info : accepting 'gdb' connection on tcp/3333
[CYW20820A1.cpu] halted due to debug-request, current mode: Thread
xPSR: 0x61000000 pc: 0x0050dc42 psp: 0x00227670
Warn : Prefer GDB command "target extended-remote :3333" instead of "target remote :3333"
===== arm v7m registers
I am using the chip cyble222014 to test Bluetooth communication, currently using mini program4 5pin port to program but it says Psoc device is not acquired, I have carefully checked the connection everywhere, so anyone understand how it is,what is wrong, thank you very much
Show LessHi~
I'd like to import sameple application named 'Hello Sensor ' from based on CYW20706 to CYBT-343026-01
Because there is no sample applicaion which has same name in CYBT-343026-01
After installing sample application, I tried to exchange BSP from CYW20706 to CYBT-343026-01.
I found some decription indicates successful, But some otheres were not.
Operation is okay after build and flash. But I'm still curious whether it is really okay or not.
Please make me sure it
I attahced error code picture
Many thanks
BRs
Daniel Lim
Show Less
I imported an example AUDIO WATCH using Modus Toolbox. After successfully build, when i try to debug it using GDB OpenOCD debugging i get the below error :
All jumper settings are Default.
Info : auto-selecting first available session transport "swd". To override use 'transport select <transport>'.
cortex_m reset_config sysresetreq
force hard breakpoints
Info : Listening on port 6666 for tcl connections
Info : Listening on port 4444 for telnet connections
Info : Using CMSIS-DAPv2 interface with VID:PID=0x04b4:0xf169, serial=180E0EE8021D2400
Info : CMSIS-DAP: SWD supported
Info : CMSIS-DAP: Atomic commands supported
Info : CMSIS-DAP: FW Version = 2.0.0
Info : CMSIS-DAP: Interface Initialised (SWD)
Info : SWCLK/TCK = 1 SWDIO/TMS = 1 TDI = 1 TDO = 1 nTRST = 0 nRESET = 1
Info : CMSIS-DAP: Interface ready
Info : KitProg3: FW version: 2.50.1383
Info : KitProg3: Pipelined transfers enabled
Info : KitProg3: Asynchronous USB transfers enabled
Info : VTarget = 2.990 V
Info : clock speed 10000 kHz
Started by GNU MCU Eclipse
Started by GNU MCU Eclipse
Error: Error connecting DP: cannot read IDR
Error: Error connecting DP: cannot read IDR
Error: Error connecting DP: cannot read IDR
Error: DAP 'CYW20820A1.cpu' initialization failed (check connection, power, transport, DAP is enabled etc.)
Kindly guide be on debugging.
Thanks,
Show Less