USB low-full-high speed peripherals Forum Discussions
Hy everyone
I'm trying to send a signal from the ztex board USB-FPGA Module 2.13 using a USB 2.0 to the computer. From the side of the fpga, I'm using a fifo code, and from the computer side, I have a java code given by ZTex specific for communication with fpga. When I test if there is any informations received, i obtain this error that I don't really understand since this is the first time I test such programs:
Error: Error receiving data: Input/Output Error
Can you help me find a solution to this error so as I can send data from fpga to computer? Thanks in advance. Tell me if you need to see the java code and vhdl project. Thanks in advance
Show LessI have a folder driver for printer which is used for win 10 (intel) and they include 3 files: cyusb3.sys, cyusb3.cat, cyusb3.inf. I tried to install them on windows 11 arm-based but it says unable to find these driver. I have been searching long while and found out there is way to convert them to arm-based (I am not giving the link cuz this come from another site)
Can anyone please help me if there is a document or tutorial of this topic?
Kindly thanks for your support
Show LessDear Friend
I want to build a data acquisition board with a FPGA sending data to PC via USB port. I think CY7C68015A/CY7C68016A is a good choice for data transfer in between FPGA and PC. But I never used this Cypress chip before, Is there any direct reference design for me to have a quick adoption with minimum effort?
Thank you so much for your help.
Regards
Tony
Show Less
请问下 CY7C68013A怎样配置USB进入test packet mode 以测试USB信号眼图一致性?有没有具体的寄存器配置指导?
Hello, I would like to ask what is the maximum sampling period for reading sensor data with cy7c65211A chip as the master and the corresponding sensor as the slave. Currently, while(1) the main cycle has been testing to read the data of a certain register of the sensor, the size is one byte, and check the pin waveform of MISO through the oscilloscope. It is found that the sampling period is only 400us-600us, is this already the highest sampling period? Please reply when you are free, thank you, and wish you a smooth work.
Show Less
Need download link for SuiteUSB, has it been obsoleted? If yes, what is its replacement?
Hi, I'm using Cypress 68013 to transfer the data from Medical Device EEG amplifier to computer with high-speed USB.
When transferring, there is a high frequency knife working around the EEG device. The high-frequency electromagnet wave will interrupt the USB transfer.
Would you please help to give some possible solutions to solve the USB working with the high frequency knife?
Thanks,
Allen
Show LessHello,
While using a board using a cyusb3014 chip, I have a question about the debug interface in chapter 5.9, AN75779.
In general use,
When I download the firmware image to the I2C EEPROM, it appears on the FX3 on "other devices".
The update driver software changes the device to the Cypress FX3 USB Streamer Example and is available for normal use.
However,
If I change the device to the boot loader and download the same firmware back to I2C EEPROM,
the UVC camera retains the camera device, but the Cypress FX3 USB Streamer Example device is not maintained and is connected back to the FX3 on "other devices".
Is there a way to keep this as a Cypress FX3 USB Streamer Example? Even if firmware is downloaded again.
Thanks.
Hi,
I'm using CY7C65215-32LTXI in our design.
I have changed the configuration like following by using USB-Serial Configuration Utility.
Before:
SCB0
Mode:I2C
Protocol:Vendor
SCB1
Mode:SPI
Protocol:Vendor
After:
SCB0
Mode:UART
Protocol:CDC
SCB1
Mode:UART
Protocol:CDC
After this change, there have been no device detected by usb-serial configurariton utility. And also device manager could not detect com port.
Please tell me the way to back the configuration under this circumstance.
Thanks.
Show Less