Microcontrollers Forum Discussions

I can program the psoc5 using openocd now, with some caveats. However, if an NVL entry exists, it stops.

I have a project which somehow did something to the NVL.

I understand setting the Reset condition on the Pins can cause this.  However, setting the pins to Don't Care doesn't fix this problem, so I suspect something else is causing the NVL to change.

Is there *any* gui / command line interface to find out what is causing the NVL to be set? (so it can be "fixed" in the project?)

This would not normally be a problem, but using openocd to program the psoc halts when the NVL entry is in the Creator generated hex file.  I have multiple reasons for using openocd, some of which involve production machines. Others are very fast compile/debug cycle.  (https://socmaker.com/?p=1004, and https://socmaker.com/?p=1027)

If I use objcopy, could I exclude that from the elf file for the new obj?  (before making a hex file) If so, would it be by address? If so, which address?  otherwise, how would I do that exclusion?

Is there a way to use openocd to program the NVL (perhaps kitprog in kitprog mode?) (Just checking)

Thanks!

Info : Could not connect to device: MiniProg4/PSoC 61/62/63

Info : Open On-Chip Debugger 0.11.0+dev-4.4.0.2134 (2022-09-08-13:07)

Info : Licensed under GNU GPL v2

Info : For bug reports, read

Info : http://openocd.org/doc/doxygen/bugs.html

Info : DEPRECATED! use 'adapter speed' not 'adapter_khz'

Info : adapter speed: 1000 kHz

Info : adapter speed: 1500 kHz

Info : adapter speed: 1500 kHz

Info : >> do kp3 acquire

Info : Using CMSIS-DAPv2 interface with VID:PID=0x04b4:0xf151, serial=180F031D03201400

Info : CMSIS-DAP: SWD supported

Info : CMSIS-DAP: JTAG supported

Info : CMSIS-DAP: Atomic commands supported

Info : CMSIS-DAP: FW Version = 2.0.0

Info : CMSIS-DAP: Interface Initialised (SWD)

Info : SWCLK/TCK = 1 SWDIO/TMS = 1 TDI = 0 TDO = 0 nTRST = 0 nRESET = 1

Info : CMSIS-DAP: Interface ready

Info : KitProg3: FW version: 2.40.1241

Info : KitProg3: Pipelined transfers enabled

Info : KitProg3: Asynchronous USB transfers enabled

Info : VTarget = 3.319 V

Info : kitprog3: acquiring the device (mode: reset)...

Error: kitprog3: failed to acquire the device

Info : clock speed 1500 kHz

Error: Error connecting DP: cannot read IDR

Error: Error connecting DP: cannot read IDR

Error: Error connecting DP: cannot read IDR

Error: DAP 'test.cpu' initialization failed (check connection, power, transport, DAP is enabled etc.)

Info : Disconnected - MiniProg4 CMSIS-DAP BULK-180F031D03201400 FW Version 2.40.1241

I am getting above error while programming CY8C6245LQI-S3D42 using miniprog-4. There are 2 boards giving same problem. These boards were programmed earlier.  Also the programmer setup is confirmed working using another board.

Can anyone help to resolve this issue?

I am attempting to follow the "Secure Boot" SDK user guide but continually run into the same problem. When attempting to setup the "CySecureTools" workspace i get the same error 'bash: cysecuretools: command not found' i get this even though i installed it and when i attempt to reinstall  cysecuretools i got the message stating command already satisfied.  This is all done on Windows

Hi Team,

Couldn't find the CAN Mailbox definitions in SDL Libraries. Is there a way to configure the mailbox in TRAVEO 2 CYT2CL?

Thanks,
Pradeep

Hi 
I am studying the Device Firmware Upgrade code
I can change the code and make it run the FW upgrade via UART by modifying the common.mk, 

and I noted the differences when I used the original sample with the I2C interface, when the upgrade process is done, the PSoC6 cam restart/reboot. and running the cm4 code

but when I changed the interface to UART. it seems to upgrade successfully, but the EVK doesn't reboot

is there anything else I need to change besides the 

please advise

Thanks

Hi,

I want to know CYT2B75CAE this controller is supporting AUTOSAR, If yes where i will get those information,

when i browse i am not able to find the information

Hello,

Recently if I open PSoC Designer normally (not as admin) I can open projects but the top file menu ribbon is not available and I can't do any build or debugging.

If I run Designer as admin then the project does not open and I get this error:

has anyone had this problem? Any help is appreciated.

hi

i want to use the SCR in order to reduce the power consumption , and meet some block point. please check state flow bellowing :

if SW switch to SCR domain to execute, which position will sw execute next after wake up source login and exit from SCR domain ?

Step A (step A as the SW first code after reset  )?  or back to Step B?

i'm trying SPI_CPU_1_KIT_TC334_LK.. I've joined SPI_A to SPI_B (confirmed on schematic for dev kit - - i hope).

when the code runs i dont have an LED on which says the data has transfered ok -- 😞 .. sad face .

i've run it a few times and set a break point . plus used a logic analyser ..

if i disconnect the MISO / MOSI lines i receive no data .. so i know the SPI slave is getting data..  .. 

i've added this line , but nothing has changed ..