Power Management ICs Forum Discussions
Hi,
i am setting a AMD SVI2 Vboot Option like a below Picture.
But, i am not sure PowIRCenter SVC & SVD setting for loop1, 2 is correct setting for AMD-SVI2 0.9V like a below picture
also, MTP Boot Register Address is not descripted in datasheet.
So,
1. Is AMD SVI2 0.9V Vboot Option Setting(Uploaded Picture) Correct?
2. MTP Boot Register is not shown in datasheet, what is The Address in IR35204
Thank you
Show Less
Are the ECU characteristics of the TLE926x series the same?
Hi all,
We would like to measure the phase margin at EVAL_TDA38740_3.3VOUT.
Could you please check if the attached method is correct?
If it is not correct, please tell me how to measure it.
If you have the phase margin of EVAL_TDA38740_3.3VOUT, please provide it for us.
Best regards,
MS
Does the TLE9461-3ES generate an error when receiving CAN2.0B 29-bit communications?
Which controller format is 2.0A or 2.0B active or 2.0B passive?
Dear Infineon engineer,
I want to use TLE7386-3E chip to generate 5V, 3.3V, and 1.3V voltages. However, in my design, it's not for MCU. Therefore, for the pins related to reset, RO_1, RO_2, and the pins related to watchdog, WDI, WDO, can I just give them a constant high or low voltage level? That is, I don't need these monitoring functions, as long as the chip can generate voltages normally.
Your help with this matter is invaluable to me, and I thank you in advance.
Doublemint
Show LessHello,
TLF35584Q is a commonly used SBC , which frequently is combined with AURIX processors.
But I could not find a reference manual regarding configuration via SPI.
Many thanks for your support!
Show LessI need to design 2 isolated supplies. For both, I am fed by a PFC front-end with a input voltage range 350V ~ 410V. My output shall be 28V. The 1st supply should deliver 200W and the 2nd supply should deliver 400W. I was first considering the LLC topology with ICE2HS01G-DS but after going into some reference material, found that EMI will be a problem later on due to the varying frequency of the converter. I therefore am considering a forward converter topology with an active clamp. I want to use the same topology for both designs in order to re-use circuitry and minimize risk. I came across the XDPP1100 digital power controller but what I would like to verify is whether the choice of topology and controller is in fact the optimum choice. I am not space constraint but my operating temperature will be at a maximum of 65 deg C, so efficiency is critical. I do not have forced air to cool down my design so I will have to rely on conduction cooling. Some inputs or advice will be greatly appreciated.
Show LessHello,
I was looking to see what the differences in firmware for both IC chips WLC1115 and WLC1150. When I attempt to create a new applications project on Modus Toolbox I only get the peripherals option with the WLC1115 but not the WLC1150. Do both chips use the same firmware?
Thanks
Show LessHi
I don't know how to program my chip(IR32504) using PowIRCenter
Can u check my program procedure ?
In my Situation, I can connect successfully IR32504 and PowIRCenter with USB0005
But, it is hard to use the PowIRCenter for me
i am tryging to program my chip with below procedure
1. Adding a device IR32504 in PowIRCenter(Full)
2. Saving the its config file
3. Loading the config file and Writing a config file to register
But the chip is not working(no ouput voltage)
I am not sure IR32504 Config file from PowIRcenter(Full) has no problem.
Please tell me what's wrong
Thx u.
Show Less
Power Management ICs
Ask your technical questions or explore existing content!