PSoC™ 6 Forum Discussions
In the basic ADC example (clean example from New Application), how can I change the default GPIO from P10_0 as defined by VPLUS_CHANNEL_0 to another GPIO?
#define VPLUS_CHANNEL_0 (P10_0)
When I tried to reassign the GPIO for example to P9_2, the error message below is shown.
-----------------------------------------------------------
HAL: ADC using HAL
-----------------------------------------------------------
ADC initialization failed. Error: 67240192
In the Device Configurator, there is no initialization of P10_0 for the ADC. Is this hard coded somewhere?
Thanks
Gary
Show LessWhen I try to "export memory " it return a file filled with 0s, even like in the case below where I can see the register has different values.
Show Less
Hello!
I am trying to implement a simple watchdog timer on my CY8PROTO-062-4343W PSoC 6 board.
The function that I want is if the program gets stucked somewhere, for example in a while(1) loop it should reset.
I start from the example I found on Infineons GitHub page.
But if I change WDT_DEMO into WDT_RESET_DEMO. And uncomment the while(1) on line 130 I should get a device reset. But I don't.
The program gets stuck in the while(1) loop but the reset won't happend. I added a printf statement do see if I get a reset but it doesn't.
I also tried to add a if statement with SRSS_SRSS_INTR & SRSS_SRSS_INTR_WDT_MATCH_Msk inside the while(1) to see if I get a interrupt, which I do after approximately 1 second.
What can be the issue here?
Show Less
My customer is looking for purchasing this PN. could not find spec.
Can you let me know road map for this product , when it will be available? what PN is relevant etc?
Show Less
I am using ModusToolbox v3.0.0 for PSOC6 development.
Some time, it takes a very long time to start up (more than 5 minutes).
And when it takes very long to start, the build start is also very slow (more than 5 minutes to start the build after clicking the build button).
Once this happens, terminating the process and restarting does not help (most of the time).
But eventually, it would start to work normally but I am not sure what causes it to break and then work correctly again.
If I terminate the "make.exe" (as shown in the following screenshot below, the process under MTB), I get a message in the console about CY_TOOLS_PATHS not set, as if the application or process was hung up in locating something.
Here are few entries from the cylogger.log file showing the activity (which is about 7 minutes apart):
2022/10/28 11:32:29 DEBUG: Tools path resolved with modus-shell is CyRsltOrErr{Value: F:\Infineon\Tools\ModusToolbox\tools_3.0\modus-shell}.
2022/10/28 11:32:29 DEBUG: getToolsPath returning: CyRsltOrErr{Value: F:\Infineon\Tools\ModusToolbox\tools_3.0\modus-shell}.
2022/10/28 11:39:24 DEBUG: Tools path set to: F:\Infineon\Tools\ModusToolbox\tools_3.0.
2022/10/28 11:39:24 DEBUG: Preparing to resolve tools path F:\Infineon\Tools\ModusToolbox\tools_3.0 with CY_TOOL_modus-shell_BASE.
....
....
2022/10/28 11:44:59 DEBUG: Tools path resolved with modus-shell is CyRsltOrErr{Value: F:\Infineon\Tools\ModusToolbox\tools_3.0\modus-shell}.
2022/10/28 11:44:59 DEBUG: getToolsPath returning: CyRsltOrErr{Value: F:\Infineon\Tools\ModusToolbox\tools_3.0\modus-shell}.
2022/10/28 11:55:42 INFO: Showing hidden views if needed.
2022/10/28 11:55:58 INFO: Showing hidden views if needed.
Show Less
I am building a product that need to be certified as RoHS (Reduction of Hazardous substances) compliant. In order to achieve compliance I need a formal RoHS certificate for EVERY component in my system and for my assembly process stating that each individual component is RoHS compliant. If all of he components are RoHS compliant, then the product is RoHS compliant and I don't need to do extremely expensive testing for compliance.
I read one community post discussing RoHS compliance here: https://community.infineon.com/t5/Knowledge-Base-Articles/Cypress-RoHS-and-REACH-Compliance-KBA211063/ta-p/255766 but when I followed the link to the RoHS document it did not take me to the correct place to find the document.
In addition to RoHS compliance I also need formal proof that the parts meet UL 94 V-0 flammability requirements.
I did find this document https://www.infineon.com/dgdl/Infineon-QTP_42902_48-Lead_TSOP_I_&_54-Lead_TSOP_II_MSL3_Pb-Free_260C_Reflow_ASEK-Taiwan_(G)-ProductQualificationReport-v02_00-EN.pdf?fileId=8ac78c8c7d710014017d714e7087154f which clearly states that the mold compound meets UL 94 V-0 but this specific report doesn't apply to the part I am using.
Many other semiconductor companies have blanket statements that indicate that the mold compounds of all their parts meet UL 94 V-0, this would be acceptable. Other companies explicitly state in each data sheet the part meets UL 94 V-0, this would also be acceptable.
The part I am using is CY8C624ABZI-S2D44. Where do I find the appropriate documents?
Show LessHello Folks,
I'm trying to interface an external NOR flash with the CY8C6244AZI-S4D82 BSP, but I haven't been able to do so, I have a few questions regarding this.
1) Can the Serial Flash Library be used with the CY8C6244AZI-S4D82 BSP?
2) Please guide me if serial flash library support with CY8C6244AZI-S4D82, how to do that?
I have tried to use BSP Asistant 1.0 and add library but I am not getting serial flash library option.
Thank you
Abhay
Show LessXin chào các bạn!
Mình đang tìm hiểu về PSoC 063 BLE Prototyping kit về các vấn đề như: chế độ hoạt động, chế độ nguồn điện thấp, cấu trúc, chức năng ngoại vi, Bluetooth tiết kiệm năng lượng, dòng cấp, dòng tiêu thụ,... Tuy nhiên mình chưa tìm được tài liệu nào đáng tin cậy! Có bác nào có tài liệu về cái này không?
Cảm ơn!
Show Less
Hi everybody!
I am working on a project where I use PSoC 063 BLE prototyping kit and modus toolbox software to read sensor and read condition from sensor to control water pump motor. I I don't know if I can use PWM it in this case or not! and how it should be done! i found some examples of PWM led, is it useful for this case?
Thank you!
Currently I am started to design firmware of PSOC6 CY8C6245AZI - S3D72 . But that PSOC not available in Both PSOC creator and Modus Toolbox. Do you know how to add that PSOC in modus software.
Show Less