PSoC™ 5, 3 & 1 Forum Discussions
Anybody know how to go to a bookmark in PSoC Creator? Have the ability to place bookmarks in files but can't seem to find a "go to next book mark" function.
Show LessOK, we have found the I2S devices and would like to know if it can be used for MPU TO MPU 64-bit data transfers (no sound).
We would like to setup a mirrored set of registers between two 5LP MPUs using DMA transfers.
We are hoping to accomplish the DMA mirroring as a transparent action.
BTW, we have not completed any DMA functions, we will be researching and testing sample code while we wait for a reply.
We found we can use three I2S Masters with a good build in one 5LP device, all of our other signals are GPIO interconnections.
Thanks in advance for your help.
Show Less
So I'm trying to make a breathing LED without using a PWM. The thought here is to try and simulate a PWM using counters, comparators and whatever else necessary to increase and decrease the duty cycle that way. However, I have trouble finding good info on how to get started on this. Any advice?
Show Lesssmartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E7%94%B5%E6%BA%90%E7%AE%A1%E7%90%86%E8%8A%AF%E7%89%87/TLE9261SBC%E7%9A%84Sleep-Mode%E9%80%89%E6%8B%A9SWK%E7%9A%84%E6%9D%A1%E4%BB%B6%E4%B8%8B-%E5%94%A4%E9%86%92%E5%BF%85%E9%A1%BB%E8%A6%81WUF%E5%90%97/td-p/656348
Show LessWhat is the max number of i2c channels I may program into the CY8C5888LTQ-LP097 device?
Using the Del-Sigma A/D on the CYC8kit-5LP at 8 bits, but when increasing to 10 bits or more, the error increases.
I'm using a UART to display measurements to a terminal
The component is configured as:
If my input is 4.002V (accuracy +- 1mV) ,
Then with A/D spits out 4023 mV. which is within 1LSB of error.
Change the A/D to 10bits and the A/D gives 4053mV
Change the A/D to 12 bits and I get : 4061mV
14bits gives 4063mV.
Any Idea as to what I'm doing wrong?
Show Less
Hello Team,
I need support writing to the pin.
Currently I am using all the pins as output GPIO pins. So i want by default for all of them to be low and then I want to make either of the GPIO high at a single time.
considering the above attached addressing.
My slave address is 0x42 since I have used A1-A6 as GPIO and A0 is pulled High with 330E.
TO write to GPIO0 bit 2
So would it be 42h 08h 02h?
Kindly let me know if this is correct.
Thank you
Show LessWe need to design a custom board using PSoC5LP.
However, we do not want to use the existing MiniProg3 for the write method, so we are looking for an on-board programming method.
The development board uses the EZ-USB FX2LP "CY7C68013A-56LTXC" and we need to develop using this IC.
Please give us more details about this kind of on-board programming. Also, please let me know if there are other approaches.
Thank you.
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/PSoC-5-3-1/On-board-Programming-of-PSoC5LP/td-p/652671
Show LessHello everyone,
attached the gerber files and schematics of a board devlepoded by the students of my robotics
course to use Arduino shields with CY8CKIT-059.
The 4 pins connectors are seeed compatible.
Hope can be helpful
Show Less