PSoC™ 5, 3 & 1 Forum Discussions
So I original chose the CY8C5267LTI-LP089 for my design. I created a custom component to do some video overlay stuff and it worked. However, I needed CAN so it was recommended that I go with the CY8C5667LTI-LP009. I swapped the parts on my prototype and my custom component doesn't work anymore. Everything else works fine (i.e. CAN, I2C, etc) so I know the new part is working. Are there any differences between these two parts that could cause my custom component to break?
Show Less hey all,
I am trying to connect my psoc 5lp kit to GSM SIM900 Using UART
So I've Connected Psoc's UART Tx to GSM Rx and vice versa on 9600 BaudRate
When I send a Dial AT Command using UART_PutString("ATD9546213"); nothing Happened
Can any one Help me PLZ
Thanks all,
New to the forums, just started using PSoC and the board that I have. Currently working an small project, as we are supposed to use an on board potentiometer to adjust an on board LED brightness. We are also supposed to report the 16 bit value to the LCD character display. I have managed to perform both of these steps, however there appears to be some sort of noise, as my least significant digit fluctuates.
Source Code:
int main()
{
LCD_Char_Start();
PWM_1_Start();
ADC1_Start();
Clock_1_Start();
uint16 ADC_Val;
char buffer[5];
for(;;){
ADC_Val=ADC1_Read16();
PWM_1_WriteCompare(ADC_Val/65);
sprintf(buffer,"%04x",ADC_Val);
LCD_Char_Position(0u, 0u);
LCD_Char_PrintString(buffer);
}
}
Any suggestions?
Thanks in advance.
Show LessHello Community,
it seems a bit useless, but I can connect a bidirectional Pin with another in PSoC-Creator. Is it possible to pass trough a digital signal e.g. flashing an eeprom? Does anyone has experience with that?
Thank you and best regards,
HeDo
Show LessHi everybody,
I work on a project which need the CAN Bus. I found many topics on internet about it with excellent examples (http://www.cypress.com/?docID=44342), but it doesn't work with me... 😞
When I do the same thing, no message is sent... The only difference is I use an internal clock, but I set on 24.000MHz.
So, to check mistakes, I allowed Error Interrupts.
With the debugger, I can see many interruption when I launch:
- CAN_1_BitErrorIsr()
- CAN_1_MsgErrorIsr()
- CAN_1_BusOffIsr()
Does anybody know where come from the mistakes ?
Thank you for helping.
Show LessHi
I'm working with an audio project, and I don't know how to get 24 bit resolution from the filter to the VDAC.
My issue that the vdac is 8 bit maximum and I need 24 bits.
Can I plays 4 vdacs in paralell or can I use current DACs with diffrent resistors?
How can I change the resoltion of filter output?
Does someone knows what is the normal resolotion of audio?
Thanks a lot
Waiting for your kind help
Show LessHi there !
Anaybody knows how to get again PSoC 3.0 ?. I think is about the last Service pack version.
The rason for get again that verson is because I have an application that was working spectacular in PSoC 3.0
and doesn't want to work wiith f PSoc 3.1
It is about RF tranceiver nRF24L01P breakout board.
The only component used in the design is a SPIM 2.40.
I would like to get PSoC3 3.0 to verify if it is some mistake from myself.
Thank you very much.
Show LessI've read AN2015, and several forum posts, and I have some questions left over.
Flash protection is 3 levels. 0= unprotected. 1=external reads disabled. 2= external read/write disabled. 3= external read/all writes disabled. Levels 0,1,2 allow the cpu to write internal flash (to allow, for example, emulated eprom)
I've read on forums that even with level 3, you can erase the chip, and also have read that with level 3, you cannot erase the chip.
There is a psoc4 document (KBA87495) that indicates there are other protection modes. Maybe only for PSoC 4.
So, my question is, based on the readers experiences:
1) Is level 1 enough protection to prevent people from seeing my code?
2) If I program level 3, is my processor forever bricked if something is wrong? (With Kill on PSoC4, that appears to be true)
3) At what level does debugging stop working, or since it comes through the SWD port, does debugging *always* work?
thanks!
Show LessHello,
I've run into some interesting bugs in my code migrating from Creator 3.0 to 3.1. So, to get a better handle on things (and perhaps discover some latent bugs) I am wanting to use PC-Lint. It doesn't appear to be natively supported by the Creator IDE. So, any of you had experience utilizing PC-Lint with Creator 3.1? I'm trying to get an idea of complexity and caveats.
Thanks!
Show Less