PSoC™ 4 Forum Discussions
Hi~
I'm trying to RF regulation test for PSoC BLE module(CYBLE-222014-01)
We want to change bluetooth TX power to increase.
How can we change it? By code level or Test tool(ex Cybluetool)?
Our customer is trying to test with Cybluetool.
Many thanks
BRs
Show Less
Hello,
I'm using PSoC 4200DS MCU(part #:CY8C4245FNI-DS402) and need use LIN to wakeup MCU from deep sleep mode. One approach I researched from this forum is to use LIN Rx pin to wakeup. However, in the generated LIN slave code by using LIN Slave component, below macro is defined to 1, hence all LIN Rx wakeup related code are removed. And since LIN Rx is already locked as LIN component's Rx pin, it cannot be assigned to general GPIO, hence I'm not able to configure same Rx pin as GPIO wakeup source separately in PSoC Creator 4.4.
Could you let me know how to enable UART Rx wakeup in LIN component? And how to configure Rx pin to wakeup MCU from deep sleep mode? Thanks a lot.
//LINS_SCB.h
#define LINS_SCB_REMOVE_UART_RX_WAKEUP_IRQ (1u)
Best Regards,
Terry
Show LessHello, I've been using PSoc Creator and loved it but I'm thinking I should learn the Modus Toolkit. So I want to create a project for a device not a kit. I've been following the document:
My device on my custom board is a CY8C244PVI-422.
I've created an empty project like the documentation said and now I'm looking for the Library Manager. Where is that?
Show Less
Hello,
I found a schematic for the BLE heart rate example project in the Page 10 of the PDF at https://www.ieee.li/pdf/viewgraphs/introduction_to_ble_system_design.pdf.
However, I could not find the sample project corresponding to this schematic from Infineon website.
It will be helpful, if you could direct me to the corresponding application note or example project.
Regards,
Kurian Polachan
Show LessHi~
I'm looking for the AutoPSoC MCU for my customer.
They are looking for the MCU included UWB.
As my researching in website and datasheet, I cannot find any MCU with UWB.
Is there any MCU with UWB in infineon?
BR
Daniel Lim
Show Less
I would like to confirm the port13 architecture of PSOC4200L.
I want to use Port13 of PSoC4200L as GPIO instead of USB.
Should the power supply for the port13 bank(D+ and D-) be supplied externally through VBUS then?
In the PSoC4200L family TRM (001-97952 Rev. *D), I found a table (page58 table7-2) that associates I/O bank ports with IO Supply Sources. Port13 was not included in that table.
This description seems to require an external power supply through VBUS even when using Port13 as a GPIO.
Does GPIO port13 need no IO power supply? Or the port13 can work with another IO power rail?
Best regards,
Inoue
Show LessHi,
I have a question about PSoC4200L.
I would like to know the threshold of the input port configured to CMOS1.8V.
Only normal CMOS and LVTTL levels of VIH/VIL are mentioned in the datasheet.
For 1.8V CMOS, I would like to know the thresholds VIH/VIL.
BR,
Inoue
Show Less
Hi,
We are migrating from CYBLE-214009 to CYBLE-214015-01 because 214009 is discontinued.
In our application we use, fixed stack OTA boot loader for 214009, and is working effectively. Do we need to do any modification for making it work with CYBLE-214015-01?
Show Less