PSoC™ 4 Forum Discussions
text.format{('custom.tabs.no.results')}
Hi Everyone,
I am using a cyble-224116-01 BLE module along with PSOC Creator 4.2. I include the stdlib.h library and my code compiles correctly, however, a call to calloc() or malloc() always returns null. I was wondering if I had to do anything special for it to work properly? Or is calloc() and malloc() not operable for my device?
Regards, Uziel.
Show LessHello,
I'm using the PSoC programmer on some custom boards with CY8C5868LTI-LP038.
I can program properly most of them.
However, for 2 of them I always get this error message:
"262144 FLASH bytes
Erase Succeeded
Programing of flash starting
Failled: Time out of SPC Polling
Lost communication with chip
Status=0x82"
For the other one the message ends with "Status=0x26".
I've inspected the 5 wire connection from the programmer to the board and every thing seems OK.
I was wondering if anyone could give me a hint of what these error codes mean, so I know what to look for.
Any feedback is appreciated.
Thank you.
Show LessHello,
I am using CYBLE-224110-00 BLE module on a custom pcb with an application and the OTA upgradable stack in the Creator workspace.
The BLE component in the application is set at -6dBm tx power, and in the firmware the PA/LNA is set in high power Mode in the BLE CYBLE_EVT_STACK_ON.
Shall these settings be applied to the BLE component in the Upgradable Stack project or bypass the PA/LNA?
The problem is: while switching to OTA bootloader, the device is not shown advertising by the Android client app, but it is detected normally when running the application. So there must be some issue with the tx settings while using the BLE component from the OTA upgrade firmware.
What is advisable to configure the BLE and PA/LNA for the OTA side?
Regards.
Show LessDear friends,
now i am using CySmar v1.3 emulator tool ,but this toot only show unsupported device(Dongle model CY5677).please anyone help me how to solve this problem. I attached getting problem screenshot int the mail.
Show LessHello,
we've recently upgraded one of our projects from using PSoC Creator 4.1 with BLE component version 3.40 to PSoC Creator 4.2 with BLE component version 3.53.
The BLE component is configured as a server which should be (and previously was) discoverable by any capable device.
However we later discovered that after the transition it stopped working for the Android 8 phones we tested, while it still works with older Android phones as well as iOS and macOS devices. On Android 8 it doesn't show up on either the CySmart App or not even on the OS level.
We did not change anything in the component settings. I've attached some settings for reference.
Any ideas where the problem might be?
Thanks,
Christoph
Show Lesshi,
i am getting event of an error in HCI.
event param is 9.
Can you please tell me what might be causing this?
i am broadcasting 3 packets every few minutes:
CYBLE_API_RESULT_T result = CyBle_GappSetNumOfAdvPkts(&cyBle_discoveryModeInfo, 3u);
on init i also get error 0xc.
thanks.
Show LessHello,
I would like to check the reason why MBR3 require pulled-up on I2C line if the pins is unsed.
Basically, I2C should be used by pulled-up but if I2C is not used and does not connect to anything device, MBR3 is not controlled ever after even if MBR3 enter stard condition. So I think we can be pulled-down on I2C line.
Please let me know the reason MBR3 need pulled-up.
Best regards,
Show LessWe are planning to consider using CY8CKIT-049.
We are going to proceed with reference to "CY8CKIT-049-4xx PSoC R 4 Prototyping Kit Guide".
However, "CY8CKIT-049 4xxx Kit Only" and "CY8CKIT-049 4xxx Kit Setup" can not be installed.
Kit Only
Kit Setup
Therefore, We would like to provide us a sample project of "CY8CKIT-049-4xx PSoC R 4 Prototyping Kit Guide".
Regards,
Show LessWe are using the CYBLE-022001-00 module, and attempting to communicate via I2c with the module being a slave. We can not get a response from the module.
- Using ports P5.0 and P5.1
- Clock and Data signals look good to the module
- Have tried all available settings for SCB block including 100 and 400khz as well as both fast and slow skew
Looking for suggestions.
Show LessWe have a serious issue and cannot resolve it, please see if you can help.
On Android, when pairing, we get no services, once the pairing is accomplished via multiple reconnect events and it connects, it will work fine afterward. We are prevented from going to production because of this concern.
When we pair, with a fixed pairing code, we get an error of no services, and sometimes the BLE stack gets stuck and thinks it is connected, but the app, ours or CYSMART gets a no services response.
1. We have the crystal trim code in our BLE start event
2. We have regenerated all UUIDs in 128 bit mode
Our bundle is attached, please help out as soon as you are able, this is an urgent matter.
Show Less