- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
Where can I find design.cycapsense file.
In the presentation of Alan Hawse
https://iotexpert.com/2019/12/09/mouser-psoc-6-wifi-bt-mbed-l5-capsense-thread/
it is located here:
targets/TARGET_Cypress/TARGET_PSOC6/TARGET_CY8PROTO_062_4343w/COMPONENT_BSP_DESIGN_MODUS/design.cycapsense
But where is located 1st part of path ... i.e. targets folder ?
Thanks.
Solved! Go to Solution.
- Labels:
-
ispn:40047:1:0
-
l1:314:1:0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi PaYe_4603801,
The targets folder is the part of the mbedOS project workspace. Please check where you have created the mouser-mbed-05 project. Under that you should be finding the targets folder inside the mbed-os directory.
For example:
C:\mbedWorkspace\mouser-mbed-05\mbed-os\targets\TARGET_Cypress\TARGET_PSOC6\TARGET_CY8CPROTO_062_4343W\COMPONENT_BSP_DESIGN_MODUS
Let us know if this helps!
Regards,
Bragadeesh
Bragadeesh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi PaYe_4603801,
The targets folder is the part of the mbedOS project workspace. Please check where you have created the mouser-mbed-05 project. Under that you should be finding the targets folder inside the mbed-os directory.
For example:
C:\mbedWorkspace\mouser-mbed-05\mbed-os\targets\TARGET_Cypress\TARGET_PSOC6\TARGET_CY8CPROTO_062_4343W\COMPONENT_BSP_DESIGN_MODUS
Let us know if this helps!
Regards,
Bragadeesh
Bragadeesh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Yes ! It's the case. Thanks.
But unlike Alan's example, the file is empty.
There is no default config, so, I have to proceed with manual configuration ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi PaYe_4603801,
The mouser-mbed-05 project contains all the required configuration settings for CapSense. The user is not expected to load the capsense configuration manually. Please see the below image which I loaded from the mouser-mbed-05 project.
Please make sure the following:
1. You have chosen the correct configurator file "design.cycapsense"
2. Right click on the design.cycapsense file in some editior such as notepad++ or Code. It is an XML file. Check if the buttons and sliders are defined correctly. This will make sure you haven't accidentally replaced the design.cycapsense file
In any case, make sure you have followed these steps:
1. Copy the full path of design.cycapsense file from targets folder
2. Open the capsense configurator from MTB 2.0 installation directory \your_location\ModusToolbox\tools_2.0\capsense-configurator
3. File > Open and copy the path of design.cycapsense file.
Regards,
Bragadeesh
Bragadeesh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
After updating the capsense 2.0 library, it becomes OK.
Thanks.