Legacy microcontrollers Forum Discussions

Hi,

I'm trying to program S6J324 and S6J3360 Traveo auto R5MCU,In usually I can use FPRG.exe via JTAG using Jlink to burn TCflash.

Now I can't burn Workflash.  So I found Segger's J-Flash  support S6J324 , but it  does not have flash size .so it can not burn it.

Do you have the Segger's J-Flash device support file?  or FPRG's TcFlash  script.

I can not use Flash Memory Programmer ,Beacuse via UART is so slow。

Hi,

I am using Fujitsu Microcontroller MB9A314L.

I am interfacing Motor Rotary Encoder to read the motor rpm for the same I am trying to use the QPRC module available in microcontroller using PDL library API. I am using example code available in Cypress -> FM_PDL_2.0.1 (Library). I am using Vision Keil 5 IDE, Program build successfully without any error but I not getting any output related to QPRC module. No Intterup generated. I am also trying by reading the Position counter register and Revolution counter register but both registers shown '0' output. Also checked the PIN assignment, but PIN assignment is also kept/connected as mentioned in example(README file).

Kindly Help to solve above issue.

Thanks in advance.

Hi,

I have contacted Fujitsu/Socionext and they have told me that Fujitsu has transferred it to you under Cypress at CY2005. Is it possible for someone to check the files and tell me the password for the Fujitsu Evaluation Kit frstapack600005fme01. Your response will be greatly appreciated so it can publish it in my thesis.

Thanks,

The S6T3J300111B176A2 is available as an evaluation board for the Cypress Travero series.

It seems to be compatible with the S6J3110 series of Traveo series.

Is there any evaluation board that is specific to the CY9D560 series?

Hi,

At "2.2. Peripheral Functions" in the CY91F528's Hardware manual, there is a following description.

Built-in RAM capacity

 Main RAM

MB91F528 : 192KB + 128KB (128KB located in the AHB area, a penalty given at access)

What is a penalty given at accessing to 128KB located in the AHB area?

I recently bought a FlexRay Evaluation board from Fujitsu that comes with a Softune Workbench. Unfortunately, the installation is password protected and the email that I am supposed to contact to obtain the password is no longer valid. Is there a way to obtain the password of the installation that I bought, software version 3.6, or would I be able to obtain access to Softune another way? Thanks,

Hi everyone:

I am using S6E2CC as a development kit, I am wondering to use SEGGER Embedded Studio as my IDE, thus I need to use Flash USB Direct Programmer to get the J-link firmware into the Cypress on-board debug solution.

I already download SK-176-s6e2ccTestCode-V12.srec file and try it on Flash USB Direct Programmer. However, there is an error for downloading 'ERROR MCU:9EH No.001 Download error'. I am thinking about since the user manual guide said"connect a USB cable between CN3 and PC.", but I am connecting CN2. However, the problem is the board is not working when I connecting CN2(no power, no LED). Is it normal?? Or there is something wrong with my board? I appreciate with your suggestion, thanks!!

best regards,

Shen

Hi,

I am looking for the exact dimensions of the FM4-176L-S6E2DH:  length, width and position of the mounting holes.  I searched it, but it seems that are not available.

I need it to create a proposal. 

https://www.cypress.com/documentation/development-kitsboards/fm4-176l-s6e2dh-arm-cortex-m4-fm4-graphics-mcu-starter-kit

Thanks!