AIROC™ Wi-Fi and Wi-Fi Bluetooth Combos Forum Discussions
Which models of BLE Mesh or Matter does Combo currently support, thank you
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AIROC-Wi-Fi%E4%B8%8EWi-Fi-%E8%93%9D%E7%89%99%E7%BB%84%E5%90%88/ble-mesh/td-p/650356
Show LessHi,
I'm currently using the Murata LBEE5KL1YN-814 EVK which consists of CYW43439 module.
I've managed to load the driver package v5.15.58-2023_0901 backported for kernel v5.15.0-051500-generic on my Ubuntu 22 Virtual Machine.
However, when i connect the module to my PC, I received these READ errors:-
"[ 260.392927] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 260.420255] usb 2-1: New USB device found, idVendor=2537, idProduct=1081, bcdDevice= 1.00
[ 260.420259] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 260.420260] usb 2-1: Product: NS1081
[ 260.420261] usb 2-1: Manufacturer: Norelsys
[ 260.420262] usb 2-1: SerialNumber: 0123456789ABCDE
[ 260.525663] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 260.526797] scsi host3: usb-storage 2-1:1.0
[ 260.529196] usbcore: registered new interface driver usb-storage
[ 260.533836] usbcore: registered new interface driver uas
[ 261.553299] scsi 3:0:0:0: Direct-Access NORELSYS 1081CS0 PQ: 0 ANSI: 6
[ 262.214995] scsi 3:0:0:1: Direct-Access NORELSYS 1081CS1 PQ: 0 ANSI: 6
[ 262.216271] scsi 3:0:0:0: Attached scsi generic sg2 type 0
[ 262.216390] scsi 3:0:0:1: Attached scsi generic sg3 type 0
[ 262.224998] sd 3:0:0:0: [sdb] Media removed, stopped polling
[ 262.230592] sd 3:0:0:1: [sdc] Very big device. Trying to use READ CAPACITY(16).
[ 262.234706] sd 3:0:0:1: [sdc] Using 0xffffffff as device size
[ 262.234710] sd 3:0:0:1: [sdc] 4294967296 512-byte logical blocks: (2.20 TB/2.00 TiB)
[ 262.239138] sd 3:0:0:1: [sdc] Write Protect is off
[ 262.239140] sd 3:0:0:1: [sdc] Mode Sense: 23 00 00 00
[ 262.241159] sd 3:0:0:1: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 262.269359] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 262.283411] sd 3:0:0:1: [sdc] Very big device. Trying to use READ CAPACITY(16).
[ 262.288336] sd 3:0:0:1: [sdc] Using 0xffffffff as device size
[ 269.279218] usb 2-1: USB disconnect, device number 2
[ 269.303388] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=7s
[ 269.303392] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 269.303393] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303399] Buffer I/O error on dev sdc, logical block 0, async page read
[ 269.303424] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=0s
[ 269.303425] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 269.303425] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303427] Buffer I/O error on dev sdc, logical block 0, async page read
[ 269.303432] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=0s
[ 269.303433] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 269.303433] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303434] Buffer I/O error on dev sdc, logical block 0, async page read
[ 269.303436] ldm_validate_partition_table(): Disk read failed.
[ 269.303440] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=0s
[ 269.303441] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 269.303441] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303442] Buffer I/O error on dev sdc, logical block 0, async page read
[ 269.303447] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=0s
[ 269.303448] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 269.303448] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303449] Buffer I/O error on dev sdc, logical block 0, async page read
[ 269.303453] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=0s
[ 269.303454] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 269.303454] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303456] Buffer I/O error on dev sdc, logical block 0, async page read
[ 269.303459] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=0s
[ 269.303460] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 269.303461] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303462] Buffer I/O error on dev sdc, logical block 0, async page read
[ 269.303463] Dev sdc: unable to read RDB block 0
[ 269.303467] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=0s
[ 269.303467] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 269.303468] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303469] Buffer I/O error on dev sdc, logical block 0, async page read
[ 269.303473] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=0s
[ 269.303474] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 269.303474] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303475] Buffer I/O error on dev sdc, logical block 0, async page read
[ 269.303485] sd 3:0:0:1: [sdc] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=0s
[ 269.303486] sd 3:0:0:1: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 18 00 00 00 08 00 00
[ 269.303486] blk_update_request: I/O error, dev sdc, sector 24 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 269.303487] Buffer I/O error on dev sdc, logical block 3, async page read
[ 269.303495] sdc: unable to read partition table
[ 269.318871] sdc: detected capacity change from 4294967296 to 0
[ 269.318877] sd 3:0:0:1: [sdc] Attached SCSI removable disk"
Note that I'm using a USB to SD card reader for my connection.
Please help to assist.
Thank you.
Show LessHi Sir,
Does CYW43012 support DFS/Radar?
It seems not support after checking all firmware in fmac package by strings command.
I can't find -dfsradar in firmware tag.
Leon
Show LessHi,
I am using Wiced 6.6 for one of our exiting BLE based application. The CYW4343 wifi-Bluetooth combo module is used in this product. I have configured the device is as server.
while performing simple read operation of 10 bytes by Client it takes more than 100 msec, even though there is no application code added. it reads from BLE stack Gatt layer. I have performed this experiment using more than one client like nRF Connect. I would like to increase the speed for Gatt read and write operation. I am using MTU size 512.
Please throw some light on this.
NOTE:
I know, it is recommended to use Modus Tool Box for new designs, However this is exiting produce where already wiced6.6 had used.
Regards,
Lokraj
__PRESENT
Show LessHi Sir
I studied the datasheet and did some experiment on CYw43455. could you help me to find the answer?
1. as the datasheet of CYW43455 , it supports 7 ACL links and 3 SCO links. May I know whats the role of device with the 7ACL links ?
(1 central to 7 peripherals , or 1 peripheral to 7 centrals?)
2. if it cannot make up to 7 links , any guidelink to modifiy it ? what would be restricted to the links number ?
3. May I know why I cannot find the ACL/SCO links number to describe in ble datasheet ? such as CYW20704/6 series ?
Show Less
Loading the device db fatal: unable to access 'https://ghproxy.com/https://github.com/Infineon/device-db/': Recv failure: Connection reset by peer ERROR:there was an error retreiving the asset 'https://github.com/Infineon/device-db' commit 'release-v4.7.1' - fatal: unable to access 'https://ghproxy.com/https://github.com/Infineon/device-db/': Recv failure: Connection reset by peer command 'C:/Users/Dsq/ModusToolbox/tools_3.1/modus-shell/bin/bash -c git -C C:/Users/Dsq/.modustoolbox/global/device-db clone --quiet --origin cypress --no-checkout https://github.com/Infineon/device-db release-v4.7.1' directory '' child process exited with error code 128 ERROR:Global asset download of device-db loading completed with error. ERROR:The asyncStepComplete failed for LoadFlag DEVICE_DB. 3 error(s), 0 warning(s) Press "Retry" to try again
Show LessWe are facing this similar issue with three different configurations right now:
- with the latest drivers and latest firmware files (hostapd v2.10)
- with the latest drivers and older firmware files (hostapd v2.10)
- with the older drivers and older firmware files (hostapd v2.10)
root@tegra-ubuntu:/home/ubuntu# hostapd -B -e /dev/urandom /root/hostapd_test.conf
Line 8: unknown configuration item 'ieee80211ac'
Line 10: unknown configuration item 'require_vht'
Line 11: unknown configuration item 'vht_oper_chwidth'
Line 12: unknown configuration item 'vht_oper_centr_freq_seg0_idx'
Line 14: unknown configuration item 'vht_capab'
5 errors found in configuration file '/root/hostapd_test.conf'
Failed to set up interface with /root/hostapd_test.conf
Failed to initialize interface
Here, we are not able to set up the configuration for 40 or 80 MHz.
Show LessI am currently using MCU to drive CYW43438 module, but I cannot find any driver description documentation for this chip. Can you provide relevant documentations?
Show Lesssmartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AIROC-Wi-Fi%E4%B8%8EWi-Fi-%E8%93%9D%E7%89%99%E7%BB%84%E5%90%88/%E8%AF%B7%E9%97%AE%E5%8A%A0%E5%AF%86IC%E6%98%AF%E5%90%A6%E6%94%AF%E6%8C%81%E5%9B%BD%E5%AF%86/td-p/643612
Show Less