AIROC™ Wi-Fi and Wi-Fi Bluetooth Combos Forum Discussions
Hi,
We would like to search one WIFI /BT Combo chipset solution for our new project, the details requirement as below, Can you help on check if have suitable solution which can meet the specification, thanks!
Dual Band Wi-Fi: 802.11 a/b/g/n, 2TX x 2RX.
Bluetooth: BLE5.2, 2 Mbps, Long Range.
The chipset shall support "Matter" over Wi-Fi.
BR
Frank.
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AIROC-Wi-Fi%E4%B8%8EWi-Fi-%E8%93%9D%E7%89%99%E7%BB%84%E5%90%88/WIFI-4-802-11n-2x2-BLE-5-2-Combo-chipset-solution/td-p/715777
Show LessHi IFX,
Chip :cyw43455
1.Below setting can connected to AP1(WPA2+802.11r) .
network={
ssid="80211Rtest"
proto=RSN WPA
key_mgmt=SAE FT-PSK WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="12345678"
}
2. disconnected to AP1(WPA2+802.11r)
3.connected to AP2(WPA3) :CYW43455 can not connect to AP2(WPA3).
Is it impossible to connect to AP2(WPA3) after adding FT-PSK in wpa_supplicant.conf ?
If yes, could you give me some guidance about waht wpa_supplicant.conf setting support AP1(WPA2+802.11r) and AP2(WPA3) .
We want the same wpa_supplicant.conf setting for AP1(WPA2+802.11r) and AP2(WPA3) .
B.R.
Bill.
Show LessHi Infineon,
A while ago I opened ticket with similar issue https://community.infineon.com/t5/AIROC-Wi-Fi-MCUs/CYW43455-brcmf-sdio-bus-sleep-error-while-changing-bus-sleep-state-110/m-p/405317#M546.
As a solution the latest driver and firmware for CYW43455 was proposed.
We are now using the latest releases godizilla, and we are still seeing the issue where module is not connected and following logs are captured:
[223856.630168] ieee80211 phy0: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
[223859.190244] ieee80211 phy0: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
Here's the log we get when wl ver is run:
wl ver
18.15 RC1.67
wl0: Aug 29 2023 01:47:08 version 7.45.265 (28bca26 CY) FWID 01-b677b91b
I have a stm32H745ZI6 chip and cyw43439(Laird-Sterling-LWB-PLUS) so i doing porting ble_hello_sensor to my chips.
My project is sucess for build, but my chips not showing to my Phone for my BLE(Hello)
STM32CubeIDE version 1.14.1
STM32CubeMX version 6.10.10-RC9
GPIO USART2 RX/TX(CTS/RTS), CYBSP_POWER
TIMER LPTIM1
Can i Connecting BLE to USART? Example connecting to UART.
Show LessHi guys,
Would you please inform how to set the multiple SSIDs by calling the function named "whd_wifi_scan" in the WHD ?
Current source code describes as only one SSID set in "CY_WCM_SCAN_FILTER_TYPE_SSID" but I'd like to set the multiple SSIDs for AP scan.
I've used the AIROC-Wi-Fi-Bluetooth-STM32 Expansion Pack 1.5.0(or 1.5.1) with Enterprise-security V2.1.0 from GitHub
on STM32H747DISCO board with Murata 2AE(CYW4373) as a STA.
Regards,
- Chuta_the_Cat
Show LessAs title.
Hi team,
Could you let me know if the CYW4373 (Murata 2AE module) supports Pre-Authentication (IEEE802.11i Pre-Authentication (type A)) ?
Operation is as the STA.
The firmware and the CLM is as follows:
WLAN Firmware : wl0: Aug 1 2023 00:41:38 version 13.10.246.321 (ebd095c CY) FWID 01-1c9488f8
WLAN CLM : API: 18.1 Data: 9.10.95 Compiler: 1.35.0 ClmImport: 1.36.3 Creation: 2018-02-01 15:32:52
or
WLAN CLM : API: 18.1 Data: Murata.Type2AE Compiler: 1.35.0 ClmImport: 1.39.1 Customization: v3 23/02/09 Creation: 2023-02-09 04:01:47
Regards,
- Chuta_the_Cat
Show LessHi all,
Does anyone know how to append the "PMKID count and List" to the RSN IE in a association packet for the roaming(PMKID caching) in case of the WPA2 EAP-TLS.
I've used the AIROC-Wi-Fi-Bluetooth-STM32 Expansion Pack 1.5.0 with Enterprise-security V2.1.0 from GitHub
on STM32H747DISCO + Murata 2AE(CYW4373) board as a STA.
Of course, the STA can join to the AP and leave works well except the PMKID caching.
Regards,
Show Less