XMC™ Forum Discussions
Hope you are doing well.
When you get a chance would you mind sharing some insight into differences between TCPWM (PSoC 62) vs. CCU 4/8 (XMC 4400)?
I am using XMC1302 MCU While Flashing HEX File I have seen the Error I have attached the file with Errors Which I have Observed
Tried with J-Link software, XMC Flasher, DAVE IDE to Set and Get BMI value I cant understand why these Errors are coming
suppose I have 5 MCU with XMC1302 in these only 3 were programmed successfully remaining 2 are getting Errors
The Proper VCC is also Given to MCU XMC1302 my Custom Board
Its a serious Issue I need to Sort this ASAP... I need the solution ASAP!!!!!!!!
Thanks & regards
Hello everyone. I am writing a piece of code to continuously write on first six sectors of XMC1202; and I need to verify my writing operation. By setting action type, we can have the results in NVMSTATUS register. My question is that, "is verification performed for each block, or each page, or each sector, in the case of continuous writing to flash."
Thanks for your time ...Show Less
Greetings of the day,
Am currently working on BLDC_SCALAR_SL_XMC13 (Sensorless) example code and trying to run the Custom motor (Maxon motor (120W) ) I have done configuration as per 'XMC13 Sensorless BLDC Scalar Control Software' getting started guide but am unable to run the motor and motor state is in
Motor0_BLDC_SCALAR.msm_state = BLDC_SCALAR_MSM_MOTOR_STATE_IDENTIFICATION; and not moving to next state to sense 3BEMF voltages, what could be the reason ?
there are 2 Sensorless startup method selection
I tried both methods, by changing MOTOR0_BLDC_SCALAR_SL_MIN_BEMF_VOLTAGE value from 2 to 0.5, due to my custom motor BEMF voltage is below 150mV (approximately = 123mV) when maximum Speed applied using POTENTIOMETER and this is measured when custom motor runned in Sensored Mode
Tell me the procedure for initial startup and run motor by sensorless control, below is the startup configuration
Please resolve my issue ASAPShow Less
Dear community members,
I have a question according to "OSC_ULP Oscillator Watchdog (ULPWDG)" in chapter 126.96.36.199 in Reference Manual V3.6 of XMC4500 family.
I see that "In case of external crystal failure the clock source switches automatically to the Internal
Slow Clock Source generating f_OSI.".
I just want to ask you whether there is a possibility to check if the internal slow clock source is in use instead of the external crystal. I assumed the SCU.HDCR.RCS bit changes automatically on failure of external crystal but it does not. Is there maybe any bit I can read out for that purpose?
One Microcontroller Platform. Countless Solutions.
Infineon’s XMC™ 32-bit industrial microcontroller portfolio is designed for system cost and efficiency for demanding industrial applications.
The XMC™ microcontroller family based on ARM® Cortex®-M cores, is dedicated to applications in the segments of power conversion, factory and building automation, transportation and home appliances.
Efficient tools, software and services from evaluation until production – XMC™ ecosystem and enablement.
Download the new XMC Brochure here:
http://bit.ly/XMC_brochure_Feb2016 Show Less
Hello. I am trying to write a piece of code to jump to another section of flash (xmc1202) in keil IDE. The code is as follows:
"LDR r0, =0x10001001;" // execute program from SRAM; at 0x20002000
But unfortunately this assembly code does not work. I have no idea why it does not work. I would be grateful if you could help me. Thanks.
I would like to program BLDC_SHIELD_TLE9879 evaluation board with the XMC1100 boot kit. I have tried to find out the libraries to flash it through the SPI pin. There is a library just for the arduino. Then I tried to progtam TLE9879 directly with the j-link lite debugger on Dave and Keil. There was an already prepared program which name is BldcBcHall.uvprojx. It is giving lots of error when I tried to build it. Is that possible to flash it with XMC100? If not, what is the solution for of the following error on the already existing program?