configuration Hostapd

Tip / Sign in to post questions, reply, level up, and achieve exciting badges. Know more

cross mob
ViSh_4113431
Level 1
Level 1
5 replies posted First comment on KBA First reply posted

I'm used i.MX6UltraLite EVK with Murata 1mw module

I need to enable interworking tag(107) in Access Point, I have setup a configuration for hostapd that provide it but it is does not show up when i am scanning the Access Point, only custom Vendor Id seems supported"""

0 Likes
1 Solution
VinayakS_26
Moderator
Moderator
Moderator
100 replies posted 50 replies posted 25 replies posted

Hi,

Could you please post your hostapd.conf file. We could try to reproduce the issue at our side.

Regards

View solution in original post

0 Likes
2 Replies
VinayakS_26
Moderator
Moderator
Moderator
100 replies posted 50 replies posted 25 replies posted

Hi,

Could you please post your hostapd.conf file. We could try to reproduce the issue at our side.

Regards

0 Likes
ViSh_4113431
Level 1
Level 1
5 replies posted First comment on KBA First reply posted

##### hostapd configuration file ##############################################

# Empty lines and lines starting with # are ignored

# AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for

# management frames with the Host AP driver); wlan0 with many nl80211 drivers

# Note: This attribute can be overridden by the values supplied with the '-i'

# command line parameter.

interface=wlan0

# In case of atheros and nl80211 driver interfaces, an additional

# configuration parameter, bridge, may be used to notify hostapd if the

# interface is included in a bridge. This parameter is not used with Host AP

# driver. If the bridge parameter is not set, the drivers will automatically

# figure out the bridge interface (assuming sysfs is enabled and mounted to

# /sys) and this parameter may not be needed.

#

# For nl80211, this parameter can be used to request the AP interface to be

# added to the bridge automatically (brctl may refuse to do this before hostapd

# has been started to change the interface mode). If needed, the bridge

# interface is also created.

#bridge=br0

# Driver interface type (hostap/wired/none/nl80211/bsd);

# default: hostap). nl80211 is used with all Linux mac80211 drivers.

# Use driver=none if building hostapd as a standalone RADIUS server that does

# not control any wireless/wired driver.

# driver=hostap

driver=nl80211

# Driver interface parameters (mainly for development testing use)

# driver_params=<params>

# hostapd event logger configuration

#

# Two output method: syslog and stdout (only usable if not forking to

# background).

#

# Module bitfield (ORed bitfield of modules that will be logged; -1 = all

# modules):

# bit 0 (1) = IEEE 802.11

# bit 1 (2) = IEEE 802.1X

# bit 2 (4) = RADIUS

# bit 3 (8) = WPA

# bit 4 (16) = driver interface

# bit 5 (32) = IAPP

# bit 6 (64) = MLME

#

# Levels (minimum value for logged events):

#  0 = verbose debugging

#  1 = debugging

#  2 = informational messages

#  3 = notification

#  4 = warning

#

logger_syslog=-1

logger_syslog_level=2

logger_stdout=-1

logger_stdout_level=2

# Interface for separate control program. If this is specified, hostapd

# will create this directory and a UNIX domain socket for listening to requests

# from external programs (CLI/GUI, etc.) for status information and

# configuration. The socket file will be named based on the interface name, so

# multiple hostapd processes/interfaces can be run at the same time if more

# than one interface is used.

# /var/run/hostapd is the recommended directory for sockets and by default,

# hostapd_cli will use it when trying to connect with hostapd.

ctrl_interface=/var/run/hostapd

# Access control for the control interface can be configured by setting the

# directory to allow only members of a group to use sockets. This way, it is

# possible to run hostapd as root (since it needs to change network

# configuration and open raw sockets) and still allow GUI/CLI components to be

# run as non-root users. However, since the control interface can be used to

# change the network configuration, this access needs to be protected in many

# cases. By default, hostapd is configured to use gid 0 (root). If you

# want to allow non-root users to use the contron interface, add a new group

# and change this value to match with that group. Add users that should have

# control interface access to this group.

#

# This variable can be a group name or gid.

#ctrl_interface_group=wheel

ctrl_interface_group=0

##### IEEE 802.11 related configuration #######################################

# SSID to be used in IEEE 802.11 management frames

ssid=tTriamp-test

# Alternative formats for configuring SSID

# (double quoted string, hexdump, printf-escaped string)

#ssid2="test"

#ssid2=74657374

#ssid2=P"hello\nthere"

# UTF-8 SSID: Whether the SSID is to be interpreted using UTF-8 encoding

#utf8_ssid=1

# Country code (ISO/IEC 3166-1). Used to set regulatory domain.

# Set as needed to indicate country in which device is operating.

# This can limit available channels and transmit power.

#country_code=US

# Enable IEEE 802.11d. This advertises the country_code and the set of allowed

# channels and transmit power levels based on the regulatory limits. The

# country_code setting must be configured with the correct country for

# IEEE 802.11d functions.

# (default: 0 = disabled)

#ieee80211d=1

# Enable IEEE 802.11h. This enables radar detection and DFS support if

# available. DFS support is required on outdoor 5 GHz channels in most countries

# of the world. This can be used only with ieee80211d=1.

# (default: 0 = disabled)

#ieee80211h=1

# Add Power Constraint element to Beacon and Probe Response frames

# This config option adds Power Constraint element when applicable and Country

# element is added. Power Constraint element is required by Transmit Power

# Control. This can be used only with ieee80211d=1.

# Valid values are 0..255.

#local_pwr_constraint=3

# Set Spectrum Management subfield in the Capability Information field.

# This config option forces the Spectrum Management bit to be set. When this

# option is not set, the value of the Spectrum Management bit depends on whether

# DFS or TPC is required by regulatory authorities. This can be used only with

# ieee80211d=1 and local_pwr_constraint configured.

#spectrum_mgmt_required=1

# Operation mode (a = IEEE 802.11a (5 GHz), b = IEEE 802.11b (2.4 GHz),

# g = IEEE 802.11g (2.4 GHz), ad = IEEE 802.11ad (60 GHz); a/g options are used

# with IEEE 802.11n (HT), too, to specify band). For IEEE 802.11ac (VHT), this

# needs to be set to hw_mode=a. When using ACS (see channel parameter), a

# special value "any" can be used to indicate that any support band can be used.

# This special case is currently supported only with drivers with which

# offloaded ACS is used.

# Default: IEEE 802.11b

hw_mode=g

# Channel number (IEEE 802.11)

# (default: 0, i.e., not set)

# Please note that some drivers do not use this value from hostapd and the

# channel will need to be configured separately with iwconfig.

#

# If CONFIG_ACS build option is enabled, the channel can be selected

# automatically at run time by setting channel=acs_survey or channel=0, both of

# which will enable the ACS survey based algorithm.

channel=1

# ACS tuning - Automatic Channel Selection

# See: http://wireless.kernel.org/en/users/Documentation/acs

#

# You can customize the ACS survey algorithm with following variables:

#

# acs_num_scans requirement is 1..100 - number of scans to be performed that

# are used to trigger survey data gathering of an underlying device driver.

# Scans are passive and typically take a little over 100ms (depending on the

# driver) on each available channel for given hw_mode. Increasing this value

# means sacrificing startup time and gathering more data wrt channel

# interference that may help choosing a better channel. This can also help fine

# tune the ACS scan time in case a driver has different scan dwell times.

#

# acs_chan_bias is a space-separated list of <channel>:<bias> pairs. It can be

# used to increase (or decrease) the likelihood of a specific channel to be

# selected by the ACS algorithm. The total interference factor for each channel

# gets multiplied by the specified bias value before finding the channel with

# the lowest value. In other words, values between 0.0 and 1.0 can be used to

# make a channel more likely to be picked while values larger than 1.0 make the

# specified channel less likely to be picked. This can be used, e.g., to prefer

# the commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default

# behavior on 2.4 GHz band if no acs_chan_bias parameter is specified).

#

# Defaults:

#acs_num_scans=5

#acs_chan_bias=1:0.8 6:0.8 11:0.8

# Channel list restriction. This option allows hostapd to select one of the

# provided channels when a channel should be automatically selected.

# Channel list can be provided as range using hyphen ('-') or individual

# channels can be specified by space (' ') separated values

# Default: all channels allowed in selected hw_mode

#chanlist=100 104 108 112 116

#chanlist=1 6 11-13

# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535)

beacon_int=100

# DTIM (delivery traffic information message) period (range 1..255):

# number of beacons between DTIMs (1 = every beacon includes DTIM element)

# (default: 2)

dtim_period=2

# Maximum number of stations allowed in station table. New stations will be

# rejected after the station table is full. IEEE 802.11 has a limit of 2007

# different association IDs, so this number should not be larger than that.

# (default: 2007)

max_num_sta=255

# RTS/CTS threshold; -1 = disabled (default); range -1..65535

# If this field is not included in hostapd.conf, hostapd will not control

# RTS threshold and 'iwconfig wlan# rts <val>' can be used to set it.

rts_threshold=-1

# Fragmentation threshold; -1 = disabled (default); range -1, 256..2346

# If this field is not included in hostapd.conf, hostapd will not control

# fragmentation threshold and 'iwconfig wlan# frag <val>' can be used to set

# it.

fragm_threshold=-1

# Rate configuration

# Default is to enable all rates supported by the hardware. This configuration

# item allows this list be filtered so that only the listed rates will be left

# in the list. If the list is empty, all rates are used. This list can have

# entries that are not in the list of rates the hardware supports (such entries

# are ignored). The entries in this list are in 100 kbps, i.e., 11 Mbps = 110.

# If this item is present, at least one rate have to be matching with the rates

# hardware supports.

# default: use the most common supported rate setting for the selected

# hw_mode (i.e., this line can be removed from configuration file in most

# cases)

#supported_rates=10 20 55 110 60 90 120 180 240 360 480 540

# Basic rate set configuration

# List of rates (in 100 kbps) that are included in the basic rate set.

# If this item is not included, usually reasonable default set is used.

#basic_rates=10 20

#basic_rates=10 20 55 110

#basic_rates=60 120 240

# Short Preamble

# This parameter can be used to enable optional use of short preamble for

# frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network performance.

# This applies only to IEEE 802.11b-compatible networks and this should only be

# enabled if the local hardware supports use of short preamble. If any of the

# associated STAs do not support short preamble, use of short preamble will be

# disabled (and enabled when such STAs disassociate) dynamically.

# 0 = do not allow use of short preamble (default)

# 1 = allow use of short preamble

#preamble=1

# Station MAC address -based authentication

# Please note that this kind of access control requires a driver that uses

# hostapd to take care of management frame processing and as such, this can be

# used with driver=hostap or driver=nl80211, but not with driver=atheros.

# 0 = accept unless in deny list

# 1 = deny unless in accept list

# 2 = use external RADIUS server (accept/deny lists are searched first)

macaddr_acl=0

# Accept/deny lists are read from separate files (containing list of

# MAC addresses, one per line). Use absolute path name to make sure that the

# files can be read on SIGHUP configuration reloads.

#accept_mac_file=/etc/hostapd.accept

#deny_mac_file=/etc/hostapd.deny

# IEEE 802.11 specifies two authentication algorithms. hostapd can be

# configured to allow both of these or only one. Open system authentication

# should be used with IEEE 802.1X.

# Bit fields of allowed authentication algorithms:

# bit 0 = Open System Authentication

# bit 1 = Shared Key Authentication (requires WEP)

auth_algs=3

# Send empty SSID in beacons and ignore probe request frames that do not

# specify full SSID, i.e., require stations to know SSID.

# default: disabled (0)

# 1 = send empty (length=0) SSID in beacon and ignore probe request for

#     broadcast SSID

# 2 = clear SSID (ASCII 0), but keep the original length (this may be required

#     with some clients that do not support empty SSID) and ignore probe

#     requests for broadcast SSID

ignore_broadcast_ssid=0

# Do not reply to broadcast Probe Request frames from unassociated STA if there

# is no room for additional stations (max_num_sta). This can be used to

# discourage a STA from trying to associate with this AP if the association

# would be rejected due to maximum STA limit.

# Default: 0 (disabled)

#no_probe_resp_if_max_sta=0

# Additional vendor specific elements for Beacon and Probe Response frames

# This parameter can be used to add additional vendor specific element(s) into

# the end of the Beacon and Probe Response frames. The format for these

# element(s) is a hexdump of the raw information elements (id+len+payload for

# one or more elements)

vendor_elements=dd0411223301

# Additional vendor specific elements for (Re)Association Response frames

# This parameter can be used to add additional vendor specific element(s) into

# the end of the (Re)Association Response frames. The format for these

# element(s) is a hexdump of the raw information elements (id+len+payload for

# one or more elements)

#assocresp_elements=dd0411223301

# TX queue parameters (EDCF / bursting)

# tx_queue_<queue name>_<param>

# queues: data0, data1, data2, data3, after_beacon, beacon

# (data0 is the highest priority queue)

# parameters:

#   aifs: AIFS (default 2)

#   cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023, 2047, 4095, 8191,

#    16383, 32767)

#   cwmax: cwMax (same values as cwMin, cwMax >= cwMin)

#   burst: maximum length (in milliseconds with precision of up to 0.1 ms) for

#          bursting

#

# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e):

# These parameters are used by the access point when transmitting frames

# to the clients.

#

# Low priority / AC_BK = background

#tx_queue_data3_aifs=7

#tx_queue_data3_cwmin=15

#tx_queue_data3_cwmax=1023

#tx_queue_data3_burst=0

# Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0

#

# Normal priority / AC_BE = best effort

#tx_queue_data2_aifs=3

#tx_queue_data2_cwmin=15

#tx_queue_data2_cwmax=63

#tx_queue_data2_burst=0

# Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0

#

# High priority / AC_VI = video

#tx_queue_data1_aifs=1

#tx_queue_data1_cwmin=7

#tx_queue_data1_cwmax=15

#tx_queue_data1_burst=3.0

# Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0

#

# Highest priority / AC_VO = voice

#tx_queue_data0_aifs=1

#tx_queue_data0_cwmin=3

#tx_queue_data0_cwmax=7

#tx_queue_data0_burst=1.5

# Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3

# 802.1D Tag (= UP) to AC mappings

# WMM specifies following mapping of data frames to different ACs. This mapping

# can be configured using Linux QoS/tc and sch_pktpri.o module.

# 802.1D Tag 802.1D Designation Access Category WMM Designation

# 1 BK AC_BK Background

# 2 - AC_BK Background

# 0 BE AC_BE Best Effort

# 3 EE AC_BE Best Effort

# 4 CL AC_VI Video

# 5 VI AC_VI Video

# 6 VO AC_VO Voice

# 7 NC AC_VO Voice

# Data frames with no priority information: AC_BE

# Management frames: AC_VO

# PS-Poll frames: AC_BE

# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e):

# for 802.11a or 802.11g networks

# These parameters are sent to WMM clients when they associate.

# The parameters will be used by WMM clients for frames transmitted to the

# access point.

#

# note - txop_limit is in units of 32microseconds

# note - acm is admission control mandatory flag. 0 = admission control not

# required, 1 = mandatory

# note - Here cwMin and cmMax are in exponent form. The actual cw value used

# will be (2^n)-1 where n is the value given here. The allowed range for these

# wmm_ac_??_{cwmin,cwmax} is 0..15 with cwmax >= cwmin.

#

wmm_enabled=1

#

# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD]

# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver)

#uapsd_advertisement_enabled=1

#

# Low priority / AC_BK = background

wmm_ac_bk_cwmin=4

wmm_ac_bk_cwmax=10

wmm_ac_bk_aifs=7

wmm_ac_bk_txop_limit=0

wmm_ac_bk_acm=0

# Note: for IEEE 802.11b mode: cWmin=5 cWmax=10

#

# Normal priority / AC_BE = best effort

wmm_ac_be_aifs=3

wmm_ac_be_cwmin=4

wmm_ac_be_cwmax=10

wmm_ac_be_txop_limit=0

wmm_ac_be_acm=0

# Note: for IEEE 802.11b mode: cWmin=5 cWmax=7

#

# High priority / AC_VI = video

wmm_ac_vi_aifs=2

wmm_ac_vi_cwmin=3

wmm_ac_vi_cwmax=4

wmm_ac_vi_txop_limit=94

wmm_ac_vi_acm=0

# Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188

#

# Highest priority / AC_VO = voice

wmm_ac_vo_aifs=2

wmm_ac_vo_cwmin=2

wmm_ac_vo_cwmax=3

wmm_ac_vo_txop_limit=47

wmm_ac_vo_acm=0

# Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102

# Static WEP key configuration

#

# The key number to use when transmitting.

# It must be between 0 and 3, and the corresponding key must be set.

# default: not set

#wep_default_key=0

# The WEP keys to use.

# A key may be a quoted string or unquoted hexadecimal digits.

# The key length should be 5, 13, or 16 characters, or 10, 26, or 32

# digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or

# 128-bit (152-bit) WEP is used.

# Only the default key must be supplied; the others are optional.

# default: not set

#wep_key0=123456789a

#wep_key1="vwxyz"

#wep_key2=0102030405060708090a0b0c0d

#wep_key3=".2.4.6.8.0.23"

# Station inactivity limit

#

# If a station does not send anything in ap_max_inactivity seconds, an

# empty data frame is sent to it in order to verify whether it is

# still in range. If this frame is not ACKed, the station will be

# disassociated and then deauthenticated. This feature is used to

# clear station table of old entries when the STAs move out of the

# range.

#

# The station can associate again with the AP if it is still in range;

# this inactivity poll is just used as a nicer way of verifying

# inactivity; i.e., client will not report broken connection because

# disassociation frame is not sent immediately without first polling

# the STA with a data frame.

# default: 300 (i.e., 5 minutes)

#ap_max_inactivity=300

#

# The inactivity polling can be disabled to disconnect stations based on

# inactivity timeout so that idle stations are more likely to be disconnected

# even if they are still in range of the AP. This can be done by setting

# skip_inactivity_poll to 1 (default 0).

#skip_inactivity_poll=0

# Disassociate stations based on excessive transmission failures or other

# indications of connection loss. This depends on the driver capabilities and

# may not be available with all drivers.

#disassoc_low_ack=1

# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to

# remain asleep). Default: 65535 (no limit apart from field size)

#max_listen_interval=100

# WDS (4-address frame) mode with per-station virtual interfaces

# (only supported with driver=nl80211)

# This mode allows associated stations to use 4-address frames to allow layer 2

# bridging to be used.

#wds_sta=1

# If bridge parameter is set, the WDS STA interface will be added to the same

# bridge by default. This can be overridden with the wds_bridge parameter to

# use a separate bridge.

#wds_bridge=wds-br0

# Start the AP with beaconing disabled by default.

#start_disabled=0

# Client isolation can be used to prevent low-level bridging of frames between

# associated stations in the BSS. By default, this bridging is allowed.

#ap_isolate=1

# BSS Load update period (in BUs)

# This field is used to enable and configure adding a BSS Load element into

# Beacon and Probe Response frames.

#bss_load_update_period=50

# Fixed BSS Load value for testing purposes

# This field can be used to configure hostapd to add a fixed BSS Load element

# into Beacon and Probe Response frames for testing purposes. The format is

# <station count>:<channel utilization>:<available admission capacity>

#bss_load_test=12:80:20000

##### IEEE 802.11n related configuration ######################################

# ieee80211n: Whether IEEE 802.11n (HT) is enabled

# 0 = disabled (default)

# 1 = enabled

# Note: You will also need to enable WMM for full HT functionality.

# Note: hw_mode=g (2.4 GHz) and hw_mode=a (5 GHz) is used to specify the band.

#ieee80211n=1

# ht_capab: HT capabilities (list of flags)

# LDPC coding capability: [LDPC] = supported

# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary

# channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz

# with secondary channel above the primary channel

# (20 MHz only if neither is set)

# Note: There are limits on which channels can be used with HT40- and

# HT40+. Following table shows the channels that may be available for

# HT40- and HT40+ use per IEEE 802.11n Annex J:

# freq HT40- HT40+

# 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan)

# 5 GHz 40,48,56,64 36,44,52,60

# (depending on the location, not all of these channels may be available

# for use)

# Please note that 40 MHz channels may switch their primary and secondary

# channels if needed or creation of 40 MHz channel maybe rejected based

# on overlapping BSSes. These changes are done automatically when hostapd

# is setting up the 40 MHz channel.

# Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC]

# (SMPS disabled if neither is set)

# HT-greenfield: [GF] (disabled if not set)

# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set)

# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set)

# Tx STBC: [TX-STBC] (disabled if not set)

# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial

# streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC

# disabled if none of these set

# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set)

# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not

# set)

# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set)

# 40 MHz intolerant [40-INTOLERANT] (not advertised if not set)

# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set)

#ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40]

# Require stations to support HT PHY (reject association if they do not)

#require_ht=1

# If set non-zero, require stations to perform scans of overlapping

# channels to test for stations which would be affected by 40 MHz traffic.

# This parameter sets the interval in seconds between these scans. Setting this

# to non-zero allows 2.4 GHz band AP to move dynamically to a 40 MHz channel if

# no co-existence issues with neighboring devices are found.

#obss_interval=0

##### IEEE 802.11ac related configuration #####################################

# ieee80211ac: Whether IEEE 802.11ac (VHT) is enabled

# 0 = disabled (default)

# 1 = enabled

# Note: You will also need to enable WMM for full VHT functionality.

# Note: hw_mode=a is used to specify that 5 GHz band is used with VHT.

#ieee80211ac=1

# vht_capab: VHT capabilities (list of flags)

#

# vht_max_mpdu_len: [MAX-MPDU-7991] [MAX-MPDU-11454]

# Indicates maximum MPDU length

# 0 = 3895 octets (default)

# 1 = 7991 octets

# 2 = 11454 octets

# 3 = reserved

#

# supported_chan_width: [VHT160] [VHT160-80PLUS80]

# Indicates supported Channel widths

# 0 = 160 MHz & 80+80 channel widths are not supported (default)

# 1 = 160 MHz channel width is supported

# 2 = 160 MHz & 80+80 channel widths are supported

# 3 = reserved

#

# Rx LDPC coding capability: [RXLDPC]

# Indicates support for receiving LDPC coded pkts

# 0 = Not supported (default)

# 1 = Supported

#

# Short GI for 80 MHz: [SHORT-GI-80]

# Indicates short GI support for reception of packets transmitted with TXVECTOR

# params format equal to VHT and CBW = 80Mhz

# 0 = Not supported (default)

# 1 = Supported

#

# Short GI for 160 MHz: [SHORT-GI-160]

# Indicates short GI support for reception of packets transmitted with TXVECTOR

# params format equal to VHT and CBW = 160Mhz

# 0 = Not supported (default)

# 1 = Supported

#

# Tx STBC: [TX-STBC-2BY1]

# Indicates support for the transmission of at least 2x1 STBC

# 0 = Not supported (default)

# 1 = Supported

#

# Rx STBC: [RX-STBC-1] [RX-STBC-12] [RX-STBC-123] [RX-STBC-1234]

# Indicates support for the reception of PPDUs using STBC

# 0 = Not supported (default)

# 1 = support of one spatial stream

# 2 = support of one and two spatial streams

# 3 = support of one, two and three spatial streams

# 4 = support of one, two, three and four spatial streams

# 5,6,7 = reserved

#

# SU Beamformer Capable: [SU-BEAMFORMER]

# Indicates support for operation as a single user beamformer

# 0 = Not supported (default)

# 1 = Supported

#

# SU Beamformee Capable: [SU-BEAMFORMEE]

# Indicates support for operation as a single user beamformee

# 0 = Not supported (default)

# 1 = Supported

#

# Compressed Steering Number of Beamformer Antennas Supported:

# [BF-ANTENNA-2] [BF-ANTENNA-3] [BF-ANTENNA-4]

#   Beamformee's capability indicating the maximum number of beamformer

#   antennas the beamformee can support when sending compressed beamforming

#   feedback

# If SU beamformer capable, set to maximum value minus 1

# else reserved (default)

#

# Number of Sounding Dimensions:

# [SOUNDING-DIMENSION-2] [SOUNDING-DIMENSION-3] [SOUNDING-DIMENSION-4]

# Beamformer's capability indicating the maximum value of the NUM_STS parameter

# in the TXVECTOR of a VHT NDP

# If SU beamformer capable, set to maximum value minus 1

# else reserved (default)

#

# MU Beamformer Capable: [MU-BEAMFORMER]

# Indicates support for operation as an MU beamformer

# 0 = Not supported or sent by Non-AP STA (default)

# 1 = Supported

#

# VHT TXOP PS: [VHT-TXOP-PS]

# Indicates whether or not the AP supports VHT TXOP Power Save Mode

#  or whether or not the STA is in VHT TXOP Power Save mode

# 0 = VHT AP doesn't support VHT TXOP PS mode (OR) VHT STA not in VHT TXOP PS

#  mode

# 1 = VHT AP supports VHT TXOP PS mode (OR) VHT STA is in VHT TXOP power save

#  mode

#

# +HTC-VHT Capable: [HTC-VHT]

# Indicates whether or not the STA supports receiving a VHT variant HT Control

# field.

# 0 = Not supported (default)

# 1 = supported

#

# Maximum A-MPDU Length Exponent: [MAX-A-MPDU-LEN-EXP0]..[MAX-A-MPDU-LEN-EXP7]

# Indicates the maximum length of A-MPDU pre-EOF padding that the STA can recv

# This field is an integer in the range of 0 to 7.

# The length defined by this field is equal to

# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets

#

# VHT Link Adaptation Capable: [VHT-LINK-ADAPT2] [VHT-LINK-ADAPT3]

# Indicates whether or not the STA supports link adaptation using VHT variant

# HT Control field

# If +HTC-VHTcapable is 1

#  0 = (no feedback) if the STA does not provide VHT MFB (default)

#  1 = reserved

#  2 = (Unsolicited) if the STA provides only unsolicited VHT MFB

#  3 = (Both) if the STA can provide VHT MFB in response to VHT MRQ and if the

#      STA provides unsolicited VHT MFB

# Reserved if +HTC-VHTcapable is 0

#

# Rx Antenna Pattern Consistency: [RX-ANTENNA-PATTERN]

# Indicates the possibility of Rx antenna pattern change

# 0 = Rx antenna pattern might change during the lifetime of an association

# 1 = Rx antenna pattern does not change during the lifetime of an association

#

# Tx Antenna Pattern Consistency: [TX-ANTENNA-PATTERN]

# Indicates the possibility of Tx antenna pattern change

# 0 = Tx antenna pattern might change during the lifetime of an association

# 1 = Tx antenna pattern does not change during the lifetime of an association

#vht_capab=[SHORT-GI-80][HTC-VHT]

#

# Require stations to support VHT PHY (reject association if they do not)

#require_vht=1

# 0 = 20 or 40 MHz operating Channel width

# 1 = 80 MHz channel width

# 2 = 160 MHz channel width

# 3 = 80+80 MHz channel width

#vht_oper_chwidth=1

#

# center freq = 5 GHz + (5 * index)

# So index 42 gives center freq 5.210 GHz

# which is channel 42 in 5G band

#

#vht_oper_centr_freq_seg0_idx=42

#

# center freq = 5 GHz + (5 * index)

# So index 159 gives center freq 5.795 GHz

# which is channel 159 in 5G band

#

#vht_oper_centr_freq_seg1_idx=159

# Workaround to use station's nsts capability in (Re)Association Response frame

# This may be needed with some deployed devices as an interoperability

# workaround for beamforming if the AP's capability is greater than the

# station's capability. This is disabled by default and can be enabled by

# setting use_sta_nsts=1.

#use_sta_nsts=0

##### IEEE 802.1X-2004 related configuration ##################################

# Require IEEE 802.1X authorization

#ieee8021x=1

# IEEE 802.1X/EAPOL version

# hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL

# version 2. However, there are many client implementations that do not handle

# the new version number correctly (they seem to drop the frames completely).

# In order to make hostapd interoperate with these clients, the version number

# can be set to the older version (1) with this configuration value.

#eapol_version=2

# Optional displayable message sent with EAP Request-Identity. The first \0

# in this string will be converted to ASCII-0 (nul). This can be used to

# separate network info (comma separated list of attribute=value pairs); see,

# e.g., RFC 4284.

#eap_message=hello

#eap_message=hello\0networkid=netw,nasid=foo,portid=0,NAIRealms=example.com

# WEP rekeying (disabled if key lengths are not set or are set to 0)

# Key lengths for default/broadcast and individual/unicast keys:

# 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits)

# 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits)

#wep_key_len_broadcast=5

#wep_key_len_unicast=5

# Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once)

#wep_rekey_period=300

# EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if

# only broadcast keys are used)

eapol_key_index_workaround=0

# EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable

# reauthentication).

#eap_reauth_period=3600

# Use PAE group address (01:80:c2:00:00:03) instead of individual target

# address when sending EAPOL frames with driver=wired. This is the most common

# mechanism used in wired authentication, but it also requires that the port

# is only used by one station.

#use_pae_group_addr=1

# EAP Re-authentication Protocol (ERP) authenticator (RFC 6696)

#

# Whether to initiate EAP authentication with EAP-Initiate/Re-auth-Start before

# EAP-Identity/Request

#erp_send_reauth_start=1

#

# Domain name for EAP-Initiate/Re-auth-Start. Omitted from the message if not

# set (no local ER server). This is also used by the integrated EAP server if

# ERP is enabled (eap_server_erp=1).

#erp_domain=example.com

##### Integrated EAP server ###################################################

# Optionally, hostapd can be configured to use an integrated EAP server

# to process EAP authentication locally without need for an external RADIUS

# server. This functionality can be used both as a local authentication server

# for IEEE 802.1X/EAPOL and as a RADIUS server for other devices.

# Use integrated EAP server instead of external RADIUS authentication

# server. This is also needed if hostapd is configured to act as a RADIUS

# authentication server.

eap_server=0

# Path for EAP server user database

# If SQLite support is included, this can be set to "sqlite:/path/to/sqlite.db"

# to use SQLite database instead of a text file.

#eap_user_file=/etc/hostapd.eap_user

# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS

#ca_cert=/etc/hostapd.ca.pem

# Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS

#server_cert=/etc/hostapd.server.pem

# Private key matching with the server certificate for EAP-TLS/PEAP/TTLS

# This may point to the same file as server_cert if both certificate and key

# are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be

# used by commenting out server_cert and specifying the PFX file as the

# private_key.

#private_key=/etc/hostapd.server.prv

# Passphrase for private key

#private_key_passwd=secret passphrase

# Server identity

# EAP methods that provide mechanism for authenticated server identity delivery

# use this value. If not set, "hostapd" is used as a default.

#server_id=server.example.com

# Enable CRL verification.

# Note: hostapd does not yet support CRL downloading based on CDP. Thus, a

# valid CRL signed by the CA is required to be included in the ca_cert file.

# This can be done by using PEM format for CA certificate and CRL and

# concatenating these into one file. Whenever CRL changes, hostapd needs to be

# restarted to take the new CRL into use.

# 0 = do not verify CRLs (default)

# 1 = check the CRL of the user certificate

# 2 = check all CRLs in the certificate path

#check_crl=1

# TLS Session Lifetime in seconds

# This can be used to allow TLS sessions to be cached and resumed with an

# abbreviated handshake when using EAP-TLS/TTLS/PEAP.

# (default: 0 = session caching and resumption disabled)

#tls_session_lifetime=3600

# Cached OCSP stapling response (DER encoded)

# If set, this file is sent as a certificate status response by the EAP server

# if the EAP peer requests certificate status in the ClientHello message.

# This cache file can be updated, e.g., by running following command

# periodically to get an update from the OCSP responder:

# openssl ocsp \

# -no_nonce \

# -CAfile /etc/hostapd.ca.pem \

# -issuer /etc/hostapd.ca.pem \

# -cert /etc/hostapd.server.pem \

# -url http://ocsp.example.com:8888/ \

# -respout /tmp/ocsp-cache.der

#ocsp_stapling_response=/tmp/ocsp-cache.der

# Cached OCSP stapling response list (DER encoded OCSPResponseList)

# This is similar to ocsp_stapling_response, but the extended version defined in

# RFC 6961 to allow multiple OCSP responses to be provided.

#ocsp_stapling_response_multi=/tmp/ocsp-multi-cache.der

# dh_file: File path to DH/DSA parameters file (in PEM format)

# This is an optional configuration file for setting parameters for an

# ephemeral DH key exchange. In most cases, the default RSA authentication does

# not use this configuration. However, it is possible setup RSA to use

# ephemeral DH key exchange. In addition, ciphers with DSA keys always use

# ephemeral DH keys. This can be used to achieve forward secrecy. If the file

# is in DSA parameters format, it will be automatically converted into DH

# params. This parameter is required if anonymous EAP-FAST is used.

# You can generate DH parameters file with OpenSSL, e.g.,

# "openssl dhparam -out /etc/hostapd.dh.pem 2048"

#dh_file=/etc/hostapd.dh.pem

# OpenSSL cipher string

#

# This is an OpenSSL specific configuration option for configuring the default

# ciphers. If not set, "DEFAULT:!EXP:!LOW" is used as the default.

# See https://www.openssl.org/docs/apps/ciphers.html for OpenSSL documentation

# on cipher suite configuration. This is applicable only if hostapd is built to

# use OpenSSL.

#openssl_ciphers=DEFAULT:!EXP:!LOW

# Fragment size for EAP methods

#fragment_size=1400

# Finite cyclic group for EAP-pwd. Number maps to group of domain parameters

# using the IANA repository for IKE (RFC 2409).

#pwd_group=19

# Configuration data for EAP-SIM database/authentication gateway interface.

# This is a text string in implementation specific format. The example

# implementation in eap_sim_db.c uses this as the UNIX domain socket name for

# the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:"

# prefix. If hostapd is built with SQLite support (CONFIG_SQLITE=y in .config),

# database file can be described with an optional db=<path> parameter.

#eap_sim_db=unix:/tmp/hlr_auc_gw.sock

#eap_sim_db=unix:/tmp/hlr_auc_gw.sock db=/tmp/hostapd.db

# EAP-SIM DB request timeout

# This parameter sets the maximum time to wait for a database request response.

# The parameter value is in seconds.

#eap_sim_db_timeout=1

# Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret,

# random value. It is configured as a 16-octet value in hex format. It can be

# generated, e.g., with the following command:

# od -tx1 -v -N16 /dev/random | colrm 1 8 | tr -d ' '

#pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f

# EAP-FAST authority identity (A-ID)

# A-ID indicates the identity of the authority that issues PACs. The A-ID

# should be unique across all issuing servers. In theory, this is a variable

# length field, but due to some existing implementations requiring A-ID to be

# 16 octets in length, it is strongly recommended to use that length for the

# field to provid interoperability with deployed peer implementations. This

# field is configured in hex format.

#eap_fast_a_id=101112131415161718191a1b1c1d1e1f

# EAP-FAST authority identifier information (A-ID-Info)

# This is a user-friendly name for the A-ID. For example, the enterprise name

# and server name in a human-readable format. This field is encoded as UTF-8.

#eap_fast_a_id_info=test server

# Enable/disable different EAP-FAST provisioning modes:

#0 = provisioning disabled

#1 = only anonymous provisioning allowed

#2 = only authenticated provisioning allowed

#3 = both provisioning modes allowed (default)

#eap_fast_prov=3

# EAP-FAST PAC-Key lifetime in seconds (hard limit)

#pac_key_lifetime=604800

# EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard

# limit). The server will generate a new PAC-Key when this number of seconds

# (or fewer) of the lifetime remains.

#pac_key_refresh_time=86400

# EAP-SIM and EAP-AKA protected success/failure indication using AT_RESULT_IND

# (default: 0 = disabled).

#eap_sim_aka_result_ind=1

# Trusted Network Connect (TNC)

# If enabled, TNC validation will be required before the peer is allowed to

# connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other

# EAP method is enabled, the peer will be allowed to connect without TNC.

#tnc=1

# EAP Re-authentication Protocol (ERP) - RFC 6696

#

# Whether to enable ERP on the EAP server.

#eap_server_erp=1

##### IEEE 802.11f - Inter-Access Point Protocol (IAPP) #######################

# Interface to be used for IAPP broadcast packets

#iapp_interface=eth0

##### RADIUS client configuration #############################################

# for IEEE 802.1X with external Authentication Server, IEEE 802.11

# authentication with external ACL for MAC addresses, and accounting

# The own IP address of the access point (used as NAS-IP-Address)

own_ip_addr=127.0.0.1

# NAS-Identifier string for RADIUS messages. When used, this should be unique

# to the NAS within the scope of the RADIUS server. Please note that hostapd

# uses a separate RADIUS client for each BSS and as such, a unique

# nas_identifier value should be configured separately for each BSS. This is

# particularly important for cases where RADIUS accounting is used

# (Accounting-On/Off messages are interpreted as clearing all ongoing sessions

# and that may get interpreted as applying to all BSSes if the same

# NAS-Identifier value is used.) For example, a fully qualified domain name

# prefixed with a unique identifier of the BSS (e.g., BSSID) can be used here.

#

# When using IEEE 802.11r, nas_identifier must be set and must be between 1 and

# 48 octets long.

#

# It is mandatory to configure either own_ip_addr or nas_identifier to be

# compliant with the RADIUS protocol. When using RADIUS accounting, it is

# strongly recommended that nas_identifier is set to a unique value for each

# BSS.

#nas_identifier=ap.example.com

# RADIUS client forced local IP address for the access point

# Normally the local IP address is determined automatically based on configured

# IP addresses, but this field can be used to force a specific address to be

# used, e.g., when the device has multiple IP addresses.

#radius_client_addr=127.0.0.1

# RADIUS authentication server

#auth_server_addr=127.0.0.1

#auth_server_port=1812

#auth_server_shared_secret=secret

# RADIUS accounting server

#acct_server_addr=127.0.0.1

#acct_server_port=1813

#acct_server_shared_secret=secret

# Secondary RADIUS servers; to be used if primary one does not reply to

# RADIUS packets. These are optional and there can be more than one secondary

# server listed.

#auth_server_addr=127.0.0.2

#auth_server_port=1812

#auth_server_shared_secret=secret2

#

#acct_server_addr=127.0.0.2

#acct_server_port=1813

#acct_server_shared_secret=secret2

# Retry interval for trying to return to the primary RADIUS server (in

# seconds). RADIUS client code will automatically try to use the next server

# when the current server is not replying to requests. If this interval is set,

# primary server will be retried after configured amount of time even if the

# currently used secondary server is still working.

#radius_retry_primary_interval=600

# Interim accounting update interval

# If this is set (larger than 0) and acct_server is configured, hostapd will

# send interim accounting updates every N seconds. Note: if set, this overrides

# possible Acct-Interim-Interval attribute in Access-Accept message. Thus, this

# value should not be configured in hostapd.conf, if RADIUS server is used to

# control the interim interval.

# This value should not be less 600 (10 minutes) and must not be less than

# 60 (1 minute).

#radius_acct_interim_interval=600

# Request Chargeable-User-Identity (RFC 4372)

# This parameter can be used to configure hostapd to request CUI from the

# RADIUS server by including Chargeable-User-Identity attribute into

# Access-Request packets.

#radius_request_cui=1

# Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN

# is used for the stations. This information is parsed from following RADIUS

# attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN),

# Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value

# VLANID as a string). Optionally, the local MAC ACL list (accept_mac_file) can

# be used to set static client MAC address to VLAN ID mapping.

# 0 = disabled (default)

# 1 = option; use default interface if RADIUS server does not include VLAN ID

# 2 = required; reject authentication if RADIUS server does not include VLAN ID

#dynamic_vlan=0

# Per-Station AP_VLAN interface mode

# If enabled, each station is assigned its own AP_VLAN interface.

# This implies per-station group keying and ebtables filtering of inter-STA

# traffic (when passed through the AP).

# If the sta is not assigned to any VLAN, then its AP_VLAN interface will be

# added to the bridge given by the "bridge" configuration option (see above).

# Otherwise, it will be added to the per-VLAN bridge.

# 0 = disabled (default)

# 1 = enabled

#per_sta_vif=0

# VLAN interface list for dynamic VLAN mode is read from a separate text file.

# This list is used to map VLAN ID from the RADIUS server to a network

# interface. Each station is bound to one interface in the same way as with

# multiple BSSIDs or SSIDs. Each line in this text file is defining a new

# interface and the line must include VLAN ID and interface name separated by

# white space (space or tab).

# If no entries are provided by this file, the station is statically mapped

# to <bss-iface>.<vlan-id> interfaces.

#vlan_file=/etc/hostapd.vlan

# Interface where 802.1q tagged packets should appear when a RADIUS server is

# used to determine which VLAN a station is on.  hostapd creates a bridge for

# each VLAN.  Then hostapd adds a VLAN interface (associated with the interface

# indicated by 'vlan_tagged_interface') and the appropriate wireless interface

# to the bridge.

#vlan_tagged_interface=eth0

# Bridge (prefix) to add the wifi and the tagged interface to. This gets the

# VLAN ID appended. It defaults to brvlan%d if no tagged interface is given

# and br%s.%d if a tagged interface is given, provided %s = tagged interface

# and %d = VLAN ID.

#vlan_bridge=brvlan

# When hostapd creates a VLAN interface on vlan_tagged_interfaces, it needs

# to know how to name it.

# 0 = vlan<XXX>, e.g., vlan1

# 1 = <vlan_tagged_interface>.<XXX>, e.g. eth0.1

#vlan_naming=0

# Arbitrary RADIUS attributes can be added into Access-Request and

# Accounting-Request packets by specifying the contents of the attributes with

# the following configuration parameters. There can be multiple of these to

# add multiple attributes. These parameters can also be used to override some

# of the attributes added automatically by hostapd.

# Format: <attr_id>[:<syntax:value>]

# attr_id: RADIUS attribute type (e.g., 26 = Vendor-Specific)

# syntax: s = string (UTF-8), d = integer, x = octet string

# value: attribute value in format indicated by the syntax

# If syntax and value parts are omitted, a null value (single 0x00 octet) is

# used.

#

# Additional Access-Request attributes

# radius_auth_req_attr=<attr_id>[:<syntax:value>]

# Examples:

# Operator-Name = "Operator"

#radius_auth_req_attr=126:s:Operator

# Service-Type = Framed (2)

#radius_auth_req_attr=6:d:2

# Connect-Info = "testing" (this overrides the automatically generated value)

#radius_auth_req_attr=77:s:testing

# Same Connect-Info value set as a hexdump

#radius_auth_req_attr=77:x:74657374696e67

#

# Additional Accounting-Request attributes

# radius_acct_req_attr=<attr_id>[:<syntax:value>]

# Examples:

# Operator-Name = "Operator"

#radius_acct_req_attr=126:s:Operator

# Dynamic Authorization Extensions (RFC 5176)

# This mechanism can be used to allow dynamic changes to user session based on

# commands from a RADIUS server (or some other disconnect client that has the

# needed session information). For example, Disconnect message can be used to

# request an associated station to be disconnected.

#

# This is disabled by default. Set radius_das_port to non-zero UDP port

# number to enable.

#radius_das_port=3799

#

# DAS client (the host that can send Disconnect/CoA requests) and shared secret

#radius_das_client=192.168.1.123 shared secret here

#

# DAS Event-Timestamp time window in seconds

#radius_das_time_window=300

#

# DAS require Event-Timestamp

#radius_das_require_event_timestamp=1

#

# DAS require Message-Authenticator

#radius_das_require_message_authenticator=1

##### RADIUS authentication server configuration ##############################

# hostapd can be used as a RADIUS authentication server for other hosts. This

# requires that the integrated EAP server is also enabled and both

# authentication services are sharing the same configuration.

# File name of the RADIUS clients configuration for the RADIUS server. If this

# commented out, RADIUS server is disabled.

#radius_server_clients=/etc/hostapd.radius_clients

# The UDP port number for the RADIUS authentication server

#radius_server_auth_port=1812

# The UDP port number for the RADIUS accounting server

# Commenting this out or setting this to 0 can be used to disable RADIUS

# accounting while still enabling RADIUS authentication.

#radius_server_acct_port=1813

# Use IPv6 with RADIUS server (IPv4 will also be supported using IPv6 API)

#radius_server_ipv6=1

##### WPA/IEEE 802.11i configuration ##########################################

# Enable WPA. Setting this variable configures the AP to require WPA (either

# WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either

# wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK.

# Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice.

# For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys),

# RADIUS authentication server must be configured, and WPA-EAP must be included

# in wpa_key_mgmt.

# This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0)

# and/or WPA2 (full IEEE 802.11i/RSN):

# bit0 = WPA

# bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled)

#wpa=1

# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit

# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase

# (8..63 characters) that will be converted to PSK. This conversion uses SSID

# so the PSK changes when ASCII passphrase is used and the SSID is changed.

# wpa_psk (dot11RSNAConfigPSKValue)

# wpa_passphrase (dot11RSNAConfigPSKPassPhrase)

#wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef

#wpa_passphrase=secret passphrase

# Optionally, WPA PSKs can be read from a separate text file (containing list

# of (PSK,MAC address) pairs. This allows more than one PSK to be configured.

# Use absolute path name to make sure that the files can be read on SIGHUP

# configuration reloads.

#wpa_psk_file=/etc/hostapd.wpa_psk

# Optionally, WPA passphrase can be received from RADIUS authentication server

# This requires macaddr_acl to be set to 2 (RADIUS)

# 0 = disabled (default)

# 1 = optional; use default passphrase/psk if RADIUS server does not include

# Tunnel-Password

# 2 = required; reject authentication if RADIUS server does not include

# Tunnel-Password

#wpa_psk_radius=0

# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The

# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be

# added to enable SHA256-based stronger algorithms.

# (dot11RSNAConfigAuthenticationSuitesTable)

#wpa_key_mgmt=WPA-PSK WPA-EAP

# Set of accepted cipher suites (encryption algorithms) for pairwise keys

# (unicast packets). This is a space separated list of algorithms:

# CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0]

# TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0]

# Group cipher suite (encryption algorithm for broadcast and multicast frames)

# is automatically selected based on this configuration. If only CCMP is

# allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise,

# TKIP will be used as the group cipher.

# (dot11RSNAConfigPairwiseCiphersTable)

# Pairwise cipher for WPA (v1) (default: TKIP)

#wpa_pairwise=TKIP CCMP

# Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value)

#rsn_pairwise=CCMP

# Time interval for rekeying GTK (broadcast/multicast encryption keys) in

# seconds. (dot11RSNAConfigGroupRekeyTime)

#wpa_group_rekey=600

# Rekey GTK when any STA that possesses the current GTK is leaving the BSS.

# (dot11RSNAConfigGroupRekeyStrict)

#wpa_strict_rekey=1

# Time interval for rekeying GMK (master key used internally to generate GTKs

# (in seconds).

#wpa_gmk_rekey=86400

# Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of

# PTK to mitigate some attacks against TKIP deficiencies.

#wpa_ptk_rekey=600

# Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up

# roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN

# authentication and key handshake before actually associating with a new AP.

# (dot11RSNAPreauthenticationEnabled)

#rsn_preauth=1

#

# Space separated list of interfaces from which pre-authentication frames are

# accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all

# interface that are used for connections to other APs. This could include

# wired interfaces and WDS links. The normal wireless data interface towards

# associated stations (e.g., wlan0) should not be added, since

# pre-authentication is only used with APs other than the currently associated

# one.

#rsn_preauth_interfaces=eth0

# peerkey: Whether PeerKey negotiation for direct links (IEEE 802.11e) is

# allowed. This is only used with RSN/WPA2.

# 0 = disabled (default)

# 1 = enabled

#peerkey=1

# ieee80211w: Whether management frame protection (MFP) is enabled

# 0 = disabled (default)

# 1 = optional

# 2 = required

#ieee80211w=0

# Group management cipher suite

# Default: AES-128-CMAC (BIP)

# Other options (depending on driver support):

# BIP-GMAC-128

# BIP-GMAC-256

# BIP-CMAC-256

# Note: All the stations connecting to the BSS will also need to support the

# selected cipher. The default AES-128-CMAC is the only option that is commonly

# available in deployed devices.

#group_mgmt_cipher=AES-128-CMAC

# Association SA Query maximum timeout (in TU = 1.024 ms; for MFP)

# (maximum time to wait for a SA Query response)

# dot11AssociationSAQueryMaximumTimeout, 1...4294967295

#assoc_sa_query_max_timeout=1000

# Association SA Query retry timeout (in TU = 1.024 ms; for MFP)

# (time between two subsequent SA Query requests)

# dot11AssociationSAQueryRetryTimeout, 1...4294967295

#assoc_sa_query_retry_timeout=201

# disable_pmksa_caching: Disable PMKSA caching

# This parameter can be used to disable caching of PMKSA created through EAP

# authentication. RSN preauthentication may still end up using PMKSA caching if

# it is enabled (rsn_preauth=1).

# 0 = PMKSA caching enabled (default)

# 1 = PMKSA caching disabled

#disable_pmksa_caching=0

# okc: Opportunistic Key Caching (aka Proactive Key Caching)

# Allow PMK cache to be shared opportunistically among configured interfaces

# and BSSes (i.e., all configurations within a single hostapd process).

# 0 = disabled (default)

# 1 = enabled

#okc=1

# SAE threshold for anti-clogging mechanism (dot11RSNASAEAntiCloggingThreshold)

# This parameter defines how many open SAE instances can be in progress at the

# same time before the anti-clogging mechanism is taken into use.

#sae_anti_clogging_threshold=5

# Enabled SAE finite cyclic groups

# SAE implementation are required to support group 19 (ECC group defined over a

# 256-bit prime order field). All groups that are supported by the

# implementation are enabled by default. This configuration parameter can be

# used to specify a limited set of allowed groups. The group values are listed

# in the IANA registry:

# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9

#sae_groups=19 20 21 25 26

##### IEEE 802.11r configuration ##############################################

# Mobility Domain identifier (dot11FTMobilityDomainID, MDID)

# MDID is used to indicate a group of APs (within an ESS, i.e., sharing the

# same SSID) between which a STA can use Fast BSS Transition.

# 2-octet identifier as a hex string.

#mobility_domain=a1b2

# PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID)

# 1 to 48 octet identifier.

# This is configured with nas_identifier (see RADIUS client section above).

# Default lifetime of the PMK-RO in minutes; range 1..65535

# (dot11FTR0KeyLifetime)

#r0_key_lifetime=10000

# PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID)

# 6-octet identifier as a hex string.

# Defaults to BSSID.

#r1_key_holder=000102030405

# Reassociation deadline in time units (TUs / 1.024 ms; range 1000..65535)

# (dot11FTReassociationDeadline)

#reassociation_deadline=1000

# List of R0KHs in the same Mobility Domain

# format: <MAC address> <NAS Identifier> <128-bit key as hex string>

# This list is used to map R0KH-ID (NAS Identifier) to a destination MAC

# address when requesting PMK-R1 key from the R0KH that the STA used during the

# Initial Mobility Domain Association.

#r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f

#r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff

# And so on.. One line per R0KH.

# List of R1KHs in the same Mobility Domain

# format: <MAC address> <R1KH-ID> <128-bit key as hex string>

# This list is used to map R1KH-ID to a destination MAC address when sending

# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD

# that can request PMK-R1 keys.

#r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f

#r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff

# And so on.. One line per R1KH.

# Whether PMK-R1 push is enabled at R0KH

# 0 = do not push PMK-R1 to all configured R1KHs (default)

# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived

#pmk_r1_push=1

# Whether to enable FT-over-DS

# 0 = FT-over-DS disabled

# 1 = FT-over-DS enabled (default)

#ft_over_ds=1

##### Neighbor table ##########################################################

# Maximum number of entries kept in AP table (either for neigbor table or for

# detecting Overlapping Legacy BSS Condition). The oldest entry will be

# removed when adding a new entry that would make the list grow over this

# limit. Note! WFA certification for IEEE 802.11g requires that OLBC is

# enabled, so this field should not be set to 0 when using IEEE 802.11g.

# default: 255

#ap_table_max_size=255

# Number of seconds of no frames received after which entries may be deleted

# from the AP table. Since passive scanning is not usually performed frequently

# this should not be set to very small value. In addition, there is no

# guarantee that every scan cycle will receive beacon frames from the

# neighboring APs.

# default: 60

#ap_table_expiration_time=3600

# Maximum number of stations to track on the operating channel

# This can be used to detect dualband capable stations before they have

# associated, e.g., to provide guidance on which colocated BSS to use.

# Default: 0 (disabled)

#track_sta_max_num=100

# Maximum age of a station tracking entry in seconds

# Default: 180

#track_sta_max_age=180

# Do not reply to group-addressed Probe Request from a station that was seen on

# another radio.

# Default: Disabled

#

# This can be used with enabled track_sta_max_num configuration on another

# interface controlled by the same hostapd process to restrict Probe Request

# frame handling from replying to group-addressed Probe Request frames from a

# station that has been detected to be capable of operating on another band,

# e.g., to try to reduce likelihood of the station selecting a 2.4 GHz BSS when

# the AP operates both a 2.4 GHz and 5 GHz BSS concurrently.

#

# Note: Enabling this can cause connectivity issues and increase latency for

# discovering the AP.

#no_probe_resp_if_seen_on=wlan1

# Reject authentication from a station that was seen on another radio.

# Default: Disabled

#

# This can be used with enabled track_sta_max_num configuration on another

# interface controlled by the same hostapd process to reject authentication

# attempts from a station that has been detected to be capable of operating on

# another band, e.g., to try to reduce likelihood of the station selecting a

# 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz BSS concurrently.

#

# Note: Enabling this can cause connectivity issues and increase latency for

# connecting with the AP.

#no_auth_if_seen_on=wlan1

##### Wi-Fi Protected Setup (WPS) #############################################

# WPS state

# 0 = WPS disabled (default)

# 1 = WPS enabled, not configured

# 2 = WPS enabled, configured

#wps_state=2

# Whether to manage this interface independently from other WPS interfaces

# By default, a single hostapd process applies WPS operations to all configured

# interfaces. This parameter can be used to disable that behavior for a subset

# of interfaces. If this is set to non-zero for an interface, WPS commands

# issued on that interface do not apply to other interfaces and WPS operations

# performed on other interfaces do not affect this interface.

#wps_independent=0

# AP can be configured into a locked state where new WPS Registrar are not

# accepted, but previously authorized Registrars (including the internal one)

# can continue to add new Enrollees.

#ap_setup_locked=1

# Universally Unique IDentifier (UUID; see RFC 4122) of the device

# This value is used as the UUID for the internal WPS Registrar. If the AP

# is also using UPnP, this value should be set to the device's UPnP UUID.

# If not configured, UUID will be generated based on the local MAC address.

#uuid=12345678-9abc-def0-1234-56789abcdef0

# Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs

# that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the

# default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of

# per-device PSKs is recommended as the more secure option (i.e., make sure to

# set wpa_psk_file when using WPS with WPA-PSK).

# When an Enrollee requests access to the network with PIN method, the Enrollee

# PIN will need to be entered for the Registrar. PIN request notifications are

# sent to hostapd ctrl_iface monitor. In addition, they can be written to a

# text file that could be used, e.g., to populate the AP administration UI with

# pending PIN requests. If the following variable is set, the PIN requests will

# be written to the configured file.

#wps_pin_requests=/var/run/hostapd_wps_pin_requests

# Device Name

# User-friendly description of device; up to 32 octets encoded in UTF-8

#device_name=Wireless AP

# Manufacturer

# The manufacturer of the device (up to 64 ASCII characters)

#manufacturer=Company

# Model Name

# Model of the device (up to 32 ASCII characters)

#model_name=WAP

# Model Number

# Additional device description (up to 32 ASCII characters)

#model_number=123

# Serial Number

# Serial number of the device (up to 32 characters)

#serial_number=12345

# Primary Device Type

# Used format: <categ>-<OUI>-<subcateg>

# categ = Category as an integer value

# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for

#       default WPS OUI

# subcateg = OUI-specific Sub Category as an integer value

# Examples:

#   1-0050F204-1 (Computer / PC)

#   1-0050F204-2 (Computer / Server)

#   5-0050F204-1 (Storage / NAS)

#   6-0050F204-1 (Network Infrastructure / AP)

#device_type=6-0050F204-1

# OS Version

# 4-octet operating system version number (hex string)

#os_version=01020300

# Config Methods

# List of the supported configuration methods

# Available methods: usba ethernet label display ext_nfc_token int_nfc_token

# nfc_interface push_button keypad virtual_display physical_display

# virtual_push_button physical_push_button

#config_methods=label virtual_display virtual_push_button keypad

# WPS capability discovery workaround for PBC with Windows 7

# Windows 7 uses incorrect way of figuring out AP's WPS capabilities by acting

# as a Registrar and using M1 from the AP. The config methods attribute in that

# message is supposed to indicate only the configuration method supported by

# the AP in Enrollee role, i.e., to add an external Registrar. For that case,

# PBC shall not be used and as such, the PushButton config method is removed

# from M1 by default. If pbc_in_m1=1 is included in the configuration file,

# the PushButton config method is left in M1 (if included in config_methods

# parameter) to allow Windows 7 to use PBC instead of PIN (e.g., from a label

# in the AP).

#pbc_in_m1=1

# Static access point PIN for initial configuration and adding Registrars

# If not set, hostapd will not allow external WPS Registrars to control the

# access point. The AP PIN can also be set at runtime with hostapd_cli

# wps_ap_pin command. Use of temporary (enabled by user action) and random

# AP PIN is much more secure than configuring a static AP PIN here. As such,

# use of the ap_pin parameter is not recommended if the AP device has means for

# displaying a random PIN.

#ap_pin=12345670

# Skip building of automatic WPS credential

# This can be used to allow the automatically generated Credential attribute to

# be replaced with pre-configured Credential(s).

#skip_cred_build=1

# Additional Credential attribute(s)

# This option can be used to add pre-configured Credential attributes into M8

# message when acting as a Registrar. If skip_cred_build=1, this data will also

# be able to override the Credential attribute that would have otherwise been

# automatically generated based on network configuration. This configuration

# option points to an external file that much contain the WPS Credential

# attribute(s) as binary data.

#extra_cred=hostapd.cred

# Credential processing

#   0 = process received credentials internally (default)

#   1 = do not process received credentials; just pass them over ctrl_iface to

# external program(s)

#   2 = process received credentials internally and pass them over ctrl_iface

# to external program(s)

# Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and

# extra_cred be used to provide the Credential data for Enrollees.

#

# wps_cred_processing=1 will disabled automatic updates of hostapd.conf file

# both for Credential processing and for marking AP Setup Locked based on

# validation failures of AP PIN. An external program is responsible on updating

# the configuration appropriately in this case.

#wps_cred_processing=0

# AP Settings Attributes for M7

# By default, hostapd generates the AP Settings Attributes for M7 based on the

# current configuration. It is possible to override this by providing a file

# with pre-configured attributes. This is similar to extra_cred file format,

# but the AP Settings attributes are not encapsulated in a Credential

# attribute.

#ap_settings=hostapd.ap_settings

# WPS UPnP interface

# If set, support for external Registrars is enabled.

#upnp_iface=br0

# Friendly Name (required for UPnP)

# Short description for end use. Should be less than 64 characters.

#friendly_name=WPS Access Point

# Manufacturer URL (optional for UPnP)

#manufacturer_url=http://www.example.com/

# Model Description (recommended for UPnP)

# Long description for end user. Should be less than 128 characters.

#model_description=Wireless Access Point

# Model URL (optional for UPnP)

#model_url=http://www.example.com/model/

# Universal Product Code (optional for UPnP)

# 12-digit, all-numeric code that identifies the consumer package.

#upc=123456789012

# WPS RF Bands (a = 5G, b = 2.4G, g = 2.4G, ag = dual band, ad = 60 GHz)

# This value should be set according to RF band(s) supported by the AP if

# hw_mode is not set. For dual band dual concurrent devices, this needs to be

# set to ag to allow both RF bands to be advertized.

#wps_rf_bands=ag

# NFC password token for WPS

# These parameters can be used to configure a fixed NFC password token for the

# AP. This can be generated, e.g., with nfc_pw_token from wpa_supplicant. When

# these parameters are used, the AP is assumed to be deployed with a NFC tag

# that includes the matching NFC password token (e.g., written based on the

# NDEF record from nfc_pw_token).

#

#wps_nfc_dev_pw_id: Device Password ID (16..65535)

#wps_nfc_dh_pubkey: Hexdump of DH Public Key

#wps_nfc_dh_privkey: Hexdump of DH Private Key

#wps_nfc_dev_pw: Hexdump of Device Password

##### Wi-Fi Direct (P2P) ######################################################

# Enable P2P Device management

#manage_p2p=1

# Allow cross connection

#allow_cross_connection=1

#### TDLS (IEEE 802.11z-2010) #################################################

# Prohibit use of TDLS in this BSS

#tdls_prohibit=1

# Prohibit use of TDLS Channel Switching in this BSS

#tdls_prohibit_chan_switch=1

##### IEEE 802.11v-2011 #######################################################

# Time advertisement

# 0 = disabled (default)

# 2 = UTC time at which the TSF timer is 0

#time_advertisement=2

# Local time zone as specified in 8.3 of IEEE Std 1003.1-2004:

# stdoffset[dst[offset][,start[/time],end[/time]]]

#time_zone=EST5

# WNM-Sleep Mode (extended sleep mode for stations)

# 0 = disabled (default)

# 1 = enabled (allow stations to use WNM-Sleep Mode)

#wnm_sleep_mode=1

# BSS Transition Management

# 0 = disabled (default)

# 1 = enabled

#bss_transition=1

# Proxy ARP

# 0 = disabled (default)

# 1 = enabled

#proxy_arp=1

# IPv6 Neighbor Advertisement multicast-to-unicast conversion

# This can be used with Proxy ARP to allow multicast NAs to be forwarded to

# associated STAs using link layer unicast delivery.

# 0 = disabled (default)

# 1 = enabled

#na_mcast_to_ucast=0

##### IEEE 802.11u-2011 #######################################################

# Enable Interworking service

interworking=1

# Access Network Type

# 0 = Private network

# 1 = Private network with guest access

# 2 = Chargeable public network

# 3 = Free public network

# 4 = Personal device network

# 5 = Emergency services only network

# 14 = Test or experimental

# 15 = Wildcard

access_network_type=4

# Whether the network provides connectivity to the Internet

# 0 = Unspecified

# 1 = Network provides connectivity to the Internet

internet=1

# Additional Step Required for Access

# Note: This is only used with open network, i.e., ASRA shall ne set to 0 if

# RSN is used.

asra=1

# Emergency services reachable

esr=1

# Unauthenticated emergency service accessible

uesa=1

# Venue Info (optional)

# The available values are defined in IEEE Std 802.11u-2011, 7.3.1.34.

# Example values (group,type):

# 0,0 = Unspecified

# 1,7 = Convention Center

# 1,13 = Coffee Shop

# 2,0 = Unspecified Business

# 7,1  Private Residence

venue_group=2

venue_type=1

# Homogeneous ESS identifier (optional; dot11HESSID)

# If set, this shall be identifical to one of the BSSIDs in the homogeneous

# ESS and this shall be set to the same value across all BSSs in homogeneous

# ESS.

#hessid=02:03:04:05:06:07

# Roaming Consortium List

# Arbitrary number of Roaming Consortium OIs can be configured with each line

# adding a new OI to the list. The first three entries are available through

# Beacon and Probe Response frames. Any additional entry will be available only

# through ANQP queries. Each OI is between 3 and 15 octets and is configured as

# a hexstring.

#roaming_consortium=021122

#roaming_consortium=2233445566

# Venue Name information

# This parameter can be used to configure one or more Venue Name Duples for

# Venue Name ANQP information. Each entry has a two or three character language

# code (ISO-639) separated by colon from the venue name string.

# Note that venue_group and venue_type have to be set for Venue Name

# information to be complete.

#venue_name=eng:Example venue

#venue_name=fin:Esimerkkipaikka

# Alternative format for language:value strings:

# (double quoted string, printf-escaped string)

#venue_name=P"eng:Example\nvenue"

# Network Authentication Type

# This parameter indicates what type of network authentication is used in the

# network.

# format: <network auth type indicator (1-octet hex str)> [redirect URL]

# Network Authentication Type Indicator values:

# 00 = Acceptance of terms and conditions

# 01 = On-line enrollment supported

# 02 = http/https redirection

# 03 = DNS redirection

#network_auth_type=00

#network_auth_type=02http://www.example.com/redirect/me/here/

# IP Address Type Availability

# format: <1-octet encoded value as hex str>

# (ipv4_type & 0x3f) << 2 | (ipv6_type & 0x3)

# ipv4_type:

# 0 = Address type not available

# 1 = Public IPv4 address available

# 2 = Port-restricted IPv4 address available

# 3 = Single NATed private IPv4 address available

# 4 = Double NATed private IPv4 address available

# 5 = Port-restricted IPv4 address and single NATed IPv4 address available

# 6 = Port-restricted IPv4 address and double NATed IPv4 address available

# 7 = Availability of the address type is not known

# ipv6_type:

# 0 = Address type not available

# 1 = Address type available

# 2 = Availability of the address type not known

#ipaddr_type_availability=14

# Domain Name

# format: <variable-octet str>[,<variable-octet str>]

#domain_name=example.com,another.example.com,yet-another.example.com

# 3GPP Cellular Network information

# format: <MCC1,MNC1>[;<MCC2,MNC2>][;...]

#anqp_3gpp_cell_net=244,91;310,026;234,56

# NAI Realm information

# One or more realm can be advertised. Each nai_realm line adds a new realm to

# the set. These parameters provide information for stations using Interworking

# network selection to allow automatic connection to a network based on

# credentials.

# format: <encoding>,<NAI Realm(s)>[,<EAP Method 1>][,<EAP Method 2>][,...]

# encoding:

# 0 = Realm formatted in accordance with IETF RFC 4282

# 1 = UTF-8 formatted character string that is not formatted in

#     accordance with IETF RFC 4282

# NAI Realm(s): Semi-colon delimited NAI Realm(s)

# EAP Method: <EAP Method>[:<[AuthParam1:Val1]>][<[AuthParam2:Val2]>][...]

# EAP Method types, see:

# http://www.iana.org/assignments/eap-numbers/eap-numbers.xhtml#eap-numbers-4

# AuthParam (Table 8-188 in IEEE Std 802.11-2012):

# ID 2 = Non-EAP Inner Authentication Type

# 1 = PAP, 2 = CHAP, 3 = MSCHAP, 4 = MSCHAPV2

# ID 3 = Inner authentication EAP Method Type

# ID 5 = Credential Type

# 1 = SIM, 2 = USIM, 3 = NFC Secure Element, 4 = Hardware Token,

# 5 = Softoken, 6 = Certificate, 7 = username/password, 9 = Anonymous,

# 10 = Vendor Specific

#nai_realm=0,example.com;example.net

# EAP methods EAP-TLS with certificate and EAP-TTLS/MSCHAPv2 with

# username/password

#nai_realm=0,example.org,13[5:6],21[2:4][5:7]

# Arbitrary ANQP-element configuration

# Additional ANQP-elements with arbitrary values can be defined by specifying

# their contents in raw format as a hexdump of the payload. Note that these

# values will override ANQP-element contents that may have been specified in the

# more higher layer configuration parameters listed above.

# format: anqp_elem=<InfoID>:<hexdump of payload>

# For example, AP Geospatial Location ANQP-element with unknown location:

#anqp_elem=265:0000

# For example, AP Civic Location ANQP-element with unknown location:

#anqp_elem=266:000000

# GAS Address 3 behavior

# 0 = P2P specification (Address3 = AP BSSID) workaround enabled by default

#     based on GAS request Address3

# 1 = IEEE 802.11 standard compliant regardless of GAS request Address3

# 2 = Force non-compliant behavior (Address3 = AP BSSID for all cases)

#gas_address3=0

# QoS Map Set configuration

#

# Comma delimited QoS Map Set in decimal values

# (see IEEE Std 802.11-2012, 8.4.2.97)

#

# format:

# [<DSCP Exceptions[DSCP,UP]>,]<UP 0 range[low,high]>,...<UP 7 range[low,high]>

#

# There can be up to 21 optional DSCP Exceptions which are pairs of DSCP Value

# (0..63 or 255) and User Priority (0..7). This is followed by eight DSCP Range

# descriptions with DSCP Low Value and DSCP High Value pairs (0..63 or 255) for

# each UP starting from 0. If both low and high value are set to 255, the

# corresponding UP is not used.

#

# default: not set

#qos_map_set=53,2,22,6,8,15,0,7,255,255,16,31,32,39,255,255,40,47,255,255

##### Hotspot 2.0 #############################################################

# Enable Hotspot 2.0 support

#hs20=1

# Disable Downstream Group-Addressed Forwarding (DGAF)

# This can be used to configure a network where no group-addressed frames are

# allowed. The AP will not forward any group-address frames to the stations and

# random GTKs are issued for each station to prevent associated stations from

# forging such frames to other stations in the BSS.

#disable_dgaf=1

# OSU Server-Only Authenticated L2 Encryption Network

#osen=1

# ANQP Domain ID (0..65535)

# An identifier for a set of APs in an ESS that share the same common ANQP

# information. 0 = Some of the ANQP information is unique to this AP (default).

#anqp_domain_id=1234

# Deauthentication request timeout

# If the RADIUS server indicates that the station is not allowed to connect to

# the BSS/ESS, the AP can allow the station some time to download a

# notification page (URL included in the message). This parameter sets that

# timeout in seconds.

#hs20_deauth_req_timeout=60

# Operator Friendly Name

# This parameter can be used to configure one or more Operator Friendly Name

# Duples. Each entry has a two or three character language code (ISO-639)

# separated by colon from the operator friendly name string.

#hs20_oper_friendly_name=eng:Example operator

#hs20_oper_friendly_name=fin:Esimerkkioperaattori

# Connection Capability

# This can be used to advertise what type of IP traffic can be sent through the

# hotspot (e.g., due to firewall allowing/blocking protocols/ports).

# format: <IP Protocol>:<Port Number>:<Status>

# IP Protocol: 1 = ICMP, 6 = TCP, 17 = UDP

# Port Number: 0..65535

# Status: 0 = Closed, 1 = Open, 2 = Unknown

# Each hs20_conn_capab line is added to the list of advertised tuples.

#hs20_conn_capab=1:0:2

#hs20_conn_capab=6:22:1

#hs20_conn_capab=17:5060:0

# WAN Metrics

# format: <WAN Info>:<DL Speed>:<UL Speed>:<DL Load>:<UL Load>:<LMD>

# WAN Info: B0-B1: Link Status, B2: Symmetric Link, B3: At Capabity

#    (encoded as two hex digits)

#    Link Status: 1 = Link up, 2 = Link down, 3 = Link in test state

# Downlink Speed: Estimate of WAN backhaul link current downlink speed in kbps;

# 1..4294967295; 0 = unknown

# Uplink Speed: Estimate of WAN backhaul link current uplink speed in kbps

# 1..4294967295; 0 = unknown

# Downlink Load: Current load of downlink WAN connection (scaled to 255 = 100%)

# Uplink Load: Current load of uplink WAN connection (scaled to 255 = 100%)

# Load Measurement Duration: Duration for measuring downlink/uplink load in

# tenths of a second (1..65535); 0 if load cannot be determined

#hs20_wan_metrics=01:8000:1000:80:240:3000

# Operating Class Indication

# List of operating classes the BSSes in this ESS use. The Global operating

# classes in Table E-4 of IEEE Std 802.11-2012 Annex E define the values that

# can be used in this.

# format: hexdump of operating class octets

# for example, operating classes 81 (2.4 GHz channels 1-13) and 115 (5 GHz

# channels 36-48):

#hs20_operating_class=5173

# OSU icons

# <Icon Width>:<Icon Height>:<Language code>:<Icon Type>:<Name>:<file path>

#hs20_icon=32:32:eng:image/png:icon32:/tmp/icon32.png

#hs20_icon=64:64:eng:image/png:icon64:/tmp/icon64.png

# OSU SSID (see ssid2 for format description)

# This is the SSID used for all OSU connections to all the listed OSU Providers.

#osu_ssid="example"

# OSU Providers

# One or more sets of following parameter. Each OSU provider is started by the

# mandatory osu_server_uri item. The other parameters add information for the

# last added OSU provider.

#

#osu_server_uri=https://example.com/osu/

#osu_friendly_name=eng:Example operator

#osu_friendly_name=fin:Esimerkkipalveluntarjoaja

#osu_nai=anonymous@example.com

#osu_method_list=1 0

#osu_icon=icon32

#osu_icon=icon64

#osu_service_desc=eng:Example services

#osu_service_desc=fin:Esimerkkipalveluja

#

#osu_server_uri=...

##### Fast Session Transfer (FST) support #####################################

#

# The options in this section are only available when the build configuration

# option CONFIG_FST is set while compiling hostapd. They allow this interface

# to be a part of FST setup.

#

# FST is the transfer of a session from a channel to another channel, in the

# same or different frequency bands.

#

# For detals, see IEEE Std 802.11ad-2012.

# Identifier of an FST Group the interface belongs to.

#fst_group_id=bond0

# Interface priority within the FST Group.

# Announcing a higher priority for an interface means declaring it more

# preferable for FST switch.

# fst_priority is in 1..255 range with 1 being the lowest priority.

#fst_priority=100

# Default LLT value for this interface in milliseconds. The value used in case

# no value provided during session setup. Default is 50 ms.

# fst_llt is in 1..4294967 range (due to spec limitation, see 10.32.2.2

# Transitioning between states).

#fst_llt=100

##### Radio measurements / location ###########################################

# The content of a LCI measurement subelement

#lci=<Hexdump of binary data of the LCI report>

# The content of a location civic measurement subelement

#civic=<Hexdump of binary data of the location civic report>

# Enable neighbor report via radio measurements

#rrm_neighbor_report=1

# Publish fine timing measurement (FTM) responder functionality

# This parameter only controls publishing via Extended Capabilities element.

# Actual functionality is managed outside hostapd.

#ftm_responder=0

# Publish fine timing measurement (FTM) initiator functionality

# This parameter only controls publishing via Extended Capabilities element.

# Actual functionality is managed outside hostapd.

#ftm_initiator=0

##### TESTING OPTIONS #########################################################

#

# The options in this section are only available when the build configuration

# option CONFIG_TESTING_OPTIONS is set while compiling hostapd. They allow

# testing some scenarios that are otherwise difficult to reproduce.

#

# Ignore probe requests sent to hostapd with the given probability, must be a

# floating point number in the range [0, 1).

#ignore_probe_probability=0.0

#

# Ignore authentication frames with the given probability

#ignore_auth_probability=0.0

#

# Ignore association requests with the given probability

#ignore_assoc_probability=0.0

#

# Ignore reassociation requests with the given probability

#ignore_reassoc_probability=0.0

#

# Corrupt Key MIC in GTK rekey EAPOL-Key frames with the given probability

#corrupt_gtk_rekey_mic_probability=0.0

#

# Include only ECSA IE without CSA IE where possible

# (channel switch operating class is needed)

#ecsa_ie_only=0

##### Multiple BSSID support ##################################################

#

# Above configuration is using the default interface (wlan#, or multi-SSID VLAN

# interfaces). Other BSSIDs can be added by using separator 'bss' with

# default interface name to be allocated for the data packets of the new BSS.

#

# hostapd will generate BSSID mask based on the BSSIDs that are

# configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is

# not the case, the MAC address of the radio must be changed before starting

# hostapd (ifconfig wlan0 hw ether <MAC addr>). If a BSSID is configured for

# every secondary BSS, this limitation is not applied at hostapd and other

# masks may be used if the driver supports them (e.g., swap the locally

# administered bit)

#

# BSSIDs are assigned in order to each BSS, unless an explicit BSSID is

# specified using the 'bssid' parameter.

# If an explicit BSSID is specified, it must be chosen such that it:

# - results in a valid MASK that covers it and the dev_addr

# - is not the same as the MAC address of the radio

# - is not the same as any other explicitly specified BSSID

#

# Alternatively, the 'use_driver_iface_addr' parameter can be used to request

# hostapd to use the driver auto-generated interface address (e.g., to use the

# exact MAC addresses allocated to the device).

#

# Not all drivers support multiple BSSes. The exact mechanism for determining

# the driver capabilities is driver specific. With the current (i.e., a recent

# kernel) drivers using nl80211, this information can be checked with "iw list"

# (search for "valid interface combinations").

#

# Please note that hostapd uses some of the values configured for the first BSS

# as the defaults for the following BSSes. However, it is recommended that all

# BSSes include explicit configuration of all relevant configuration items.

#

#bss=wlan0_0

#ssid=test2

# most of the above items can be used here (apart from radio interface specific

# items, like channel)

#bss=wlan0_1

#bssid=00:13:10:95:fe:0b

# ...

0 Likes