- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear Staff,
How to enable FRS functionality using EZ-PD Config Utility?
Thx,
WH
Solved! Go to Solution.
- Labels:
-
USB EZ-PD Type-C
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Please refer to the following image on how to enable FRS using EZ-PD Config utility.
The Type C controller used here to show the FRS feature is CCG3.
Regards,
Abhilash P
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Test
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Please refer to the following image on how to enable FRS using EZ-PD Config utility.
The Type C controller used here to show the FRS feature is CCG3.
Regards,
Abhilash P
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Abhilash,
But how come mine shows "None" and grayed out? I am configuring CYPD3171-24LQXQ.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Please use the drop down option to select FRS receive and transmit options.
Regards,
Abhilash P
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Can you explain to me the meaning of "Flashing mode index = 1"? If I want to program the device thru the CC interface, any modification needs to be made?
Thx,
Will
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Also, if Rp supported sets to Default, what is the current limit?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sorry, few more terms wanted to clarify:
What are the definitions of "Is source extremally powered" and "is sink extremally powered"?
Thank you a lot
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
A device can be powered from 2 sources, it can be either bus powered or externally powered through wall power source.
Regards,
Abhilash P
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Please refer to the following table,
Rp | Rd | Vbus current limit |
56 kΩ | 5.1 kΩ | 500 or 900 mA |
22 kΩ | 5.1 kΩ | 1.5A @ 5V |
10 kΩ | 5.1 kΩ | 3A @ 5V |
For Default refer to the first row.
Regards,
Abhilash P
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear Cypress,
What is the difference between Reject and Not_SUPPORTED under DR_Swap response pull down menu?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thank you a lot Abhilash P ^^,
Can you explain to me the meaning of "Flashing mode index = 1"? If I want to program the device thru the CC interface, any modification needs to be made?
Thx,
Will
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Abhilash P,
What's the meaning of "Config table major version = 2"? Is this # always fixed?
Thx,
Will
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Abhilash P,
Under what consideration do I need to set "Sink USB suspend = Yes"? What does it mean?
Will ^^
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Will,
Please refer to the following images to get a clarity on USB suspend option,
Regards,
Abhilash P
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Abhilash,
Cleared. Is above info from USB-IF spec?
Also, what is the difference between Reject and Not_SUPPORTED under DR_Swap response pull down menu?
WH
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Also, what are the definitions of Wait, Reject and Not_SUPPORTED under DR/PR_Swap response, respectively, under pull down menu? An appropriate documentation is appreciated ^^
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Please refer to section 6.3 in USB PD Spec to know more about accept, reject and not supported options.
Regards,
Abhilash P
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Abhilash,
Do you have detailed explanation about SCEDB parameters. I don't see them in EZ-PD Configuration Utility User Manual?
Thx ^^,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
EZ-PD Configuration Utility User Manual P. 28 ^^
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Please find the description in the attached image,
Regards,
Abhilash P
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear Cypress,
What is the purpose of having below User Parameters?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
The shot is not clear. Can you please provide a more clear image or you can just mention which parameter you are referring to.
Regards,
Abhilash P