ModusToolbox™ Forum Discussions

Hello All,

I wish to use the ModusToolbox for Machine Learning as I plan to get started with ML on Infineon hardware, however, I have a few queries.

1. I understand it is supported only for PSoC 6. If there are any others, please help me with the details.
2. The hardware/development kits for PSoC 6 are as mentioned in this link but I am not sure if all of these are supported for Machine Learning.
3. Is it supported specifically for CY8CKIT-062S4?
4. Does ModusToolbox support the application features of imagimob, SensiML and Edge Impulse?

Regards,
Sabat

1、The modus Version: 3.2.0 2、'

2、I create a New application ,the procedure as below

the chip change to “CY8C4025LOI-T412” ,the clolk change from 48MHZ to 24 MHZ which was operated as the notes show //-->compile ok

The CY8C4025LOI-T412 project has 4 Buttons(P2.0 、 P2.3、 P2.4、 P2.5) and a I2C(P3.2 P3.3) that is different from the defaut prorammer .yet the progammer is changed //---compile error

#error The CAPSENSE(TM)Configurator requires anewer version of the CAPSENSE(TM)Middleware. Update the CAPSENSE(TM)Mddleware in your project.

........

#error #CY CAPSENSE BUTTON SELF CAP CLICKmain.c:176:26:error:TIMEOUT MAX VALUE'undeclared(first use in this function)

----------------------------------------------

Project-Doesn-t-Reflect-Middleware-Version-Selected-Using-BSP-Assistant 这个我不明白写的啥，按照这个操作也解决不了 .the URL could not solve my problem

My number  :17317187679

Thanks

Hi all,

I would like to try the firmware upgrade example for my dev kit. But it is not working.

Can you please advise me what I have wrong?

I am attaching an error log.

PS: I am using latest ModusToolbox v 3.2.

Best Regards

Koumak

Hi Infineon.

PSoC Creator allows flash protection with “Design Wide Resources(Flash Security)”.

Please confirm below figure.

Could you please let us know how to apply protection to flash in Modus?

Target device is PSoC4100S Max

PSoC4100S Max only supports Modus.

Best Regards.

YuMa

Hi Folks,

From the previows discussion, finally I could download Setup1.0
https://community.infineon.com/t5/ModusToolbox/Release-Announcement-ModusToolbox-v3-2-available-for-download/td-p/714363

Then when I tried to ModusToolbox setup, it did not went good.

So I removed related files, as far as I could think of, then re-downloaded

ModusToolboxSetupInstaller_1.0.0.468_windows_x64_signed.exe

launcher2_2023.9.1_Windows_x32-x64.exe

I installed both and in the Launcher I can see the SETUP

In this window, I'm already logged in as me, but allow me to hide my working mail address 😉

(At least "Log out" icon is there)

Then when I click and start the Setup, I get
Error: Failed to start Launcher Service: 'process failed to start'

and

Error: Failed to check for the ModusToolbox Setup update

Since the upper left of the ModusToolbox Setup 1.0 is saying "Login"

I clicked the "Login" Icon, then got

Error: Failed to Login: 'process failed to start'

Note: The right side of the "Login" Icon is saying "Login session is in progress" >_<

Just in case, let me note that I can login to both MyInfineon and IDC.

(1) MyInfineon 

(2) Infineon Developer Community (So, I can post this here)

Since the Setup Utility has removed my ModusToolbox 3.1,

currently I have no MTB on my PC, I'd really like to install v3.2.

Now my question is would someone teach me what the safest or the most reliable way to install MTB v3.2 is?

And/or how can I find the cause(s) of errors above?

moto