How to get articles that linked to old cypress.com?

Tip / Sign in to post questions, reply, level up, and achieve exciting badges. Know more

cross mob
Brian_D
Level 2
Level 2
First like received 10 replies posted 10 sign-ins

I was trying to debug why my MiniProg3 not recognize by my Windows 10 pc and want to see this article:

http://www.cypress.com/?id=4&rID=45812

But the link breaks up with anything cypress.com after Infineon took over, I think. How to work around this?

Brian

0 Likes
1 Solution
MotooTanaka
Level 9
Level 9
Distributor - Marubun (Japan)
First comment on blog Beta tester First comment on KBA

Hi,

I found PSoC Creator v2.2 in the PSoC Creator Archive Page

https://www.infineon.com/cms/en/design-support/tools/tools-archive/psoc-creator-archive/

as

https://www.infineon.com/dgdl/Infineon-PSoCCreatorSetup_2.2_CP6.exe-DevelopmentTools-v01_00-EN.htm?f...

When I installed this version, in the release note there was

001-release_note.JPG

So if you install this version, MiniProg3 may be supported.

moto

View solution in original post

0 Likes
7 Replies
Gautami_12
Moderator
Moderator
Moderator
50 likes received 100 solutions authored 250 replies posted

Hi @Brian_D,

Can you please let us know the context of the document that you are trying to access?

Also please let us know if miniprog3 is detected in the device manager of your PC?

Please refer to the Screenshot:

Gautami_12_0-1657773750275.png

 

Warm Regards,
Gautami J

0 Likes
MotooTanaka
Level 9
Level 9
Distributor - Marubun (Japan)
First comment on blog Beta tester First comment on KBA

Hi,

I just followed the link you posted.

With ignoring security warnings, I could access the page and the page was like below.

I wonder if this was what you needed to access, though.

PSoC3_old_article.JPG

moto

0 Likes

Hi Moto,

I was searching for solution of why plug in the MiniProg3 to a windows10 laptop with Creator 2.2 (need this old version to work with the old device CY8C5468LTI-037 PSoC) and the MiniProg3 didn't show up on the Device Manager, then found this forum thread https://community.infineon.com/t5/PSoC-5-3-1/device-not-detected/td-p/189659

"If you are not able to see the proper driver getting installed, then follow the steps mentioned in this KB article - http://www.cypress.com/?id=4&rID=45812. Instead of pointing to FTK driver as explained in the KB article, point to mprog3 driver inside the PSoC Programmer installed location."

 

and the said link that I had problem. It seems our IT blocked it for some reasons.

Thanks,

Brian

 

 

0 Likes
MotooTanaka
Level 9
Level 9
Distributor - Marubun (Japan)
First comment on blog Beta tester First comment on KBA

Hi,

I found PSoC Creator v2.2 in the PSoC Creator Archive Page

https://www.infineon.com/cms/en/design-support/tools/tools-archive/psoc-creator-archive/

as

https://www.infineon.com/dgdl/Infineon-PSoCCreatorSetup_2.2_CP6.exe-DevelopmentTools-v01_00-EN.htm?f...

When I installed this version, in the release note there was

001-release_note.JPG

So if you install this version, MiniProg3 may be supported.

moto

0 Likes

It seems Creator 2.2 might only work for Windows7 and older version. I'm installing it on a Windows7 now and will see if it works.

Brian

Good news!

I installed Creator 2.2 on Windows7 PC and it woks now. This old version doesn't work on Windows10 for sure -- the Prog3 Driver was not installed correctly. 

Thank you everyone for your inputs.

Brian

 

Gautami_12
Moderator
Moderator
Moderator
50 likes received 100 solutions authored 250 replies posted

Hi @Brian_D,

Glad your query has been resolved.

Please feel free to post any queries or issues you may have on Infineon products in the community and we will be happy to help.

Warm Regards,
Gautami J

0 Likes