- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello
I have a problem to program a CYBL10162-56LQXI
I want to use an HM-16 module from jnhuamao.cn
You can see http://www.jnhuamao.cn/bluetooth41_en.zip
This module consists mainly of a microcontroller CYBL10162-56LQXI
In base it is programmed with a firmware allowing to make AT commands and it functions correctly with a serial port.
I would like to fully reprogram the firmware with the PSOC4 Creator software
but I can not connect.
I use the USB interface of CY8CKIT-043
I connected (USB part of CY8CKIT-043 to CYBL10162-56LQXI
SWDIO to SWDIO (Pin 26 P0.6)
SWDCLK to SWDCLK (Pin 27 P0.7)
RST to XRES (Pin4 XRES)
GND to GND
VTARG to VCC
I tried to program with Psoc Creator 4.1 or with PSoCProgrammer
my CYBL10162-56LQXI is recognized but I still have an error message and programming is not done.
can you help me ?
thank you
Solved! Go to Solution.
- Labels:
-
BLE
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have investigated more.
The HM-16 i can programm (with PSOC4), had a CYBL10162 chip.
The HM-16 i can't programm, had a chip WNF101 (see picture).
I bought it from Fastech, but what is WNF101 ?
Thanks if you have some informations.
see http://onebus.fr/img/chip%20du%20module%20hm-16.jpg
Yves
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello ,
Can you check if the Kitprog is upgraded to latest.
Thanks,
Hima
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello
I am sure that my wiring (given above) is good. I found a device that uses the HM-16 module and I can program it.
On the other hand if I use a module HM-16 alone, imposible to program it.
See picture on the link (screenshot) http://onebus.fr/img/HM-16.jpg
Maybe there is a system to block progarmmation?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have investigated more.
The HM-16 i can programm (with PSOC4), had a CYBL10162 chip.
The HM-16 i can't programm, had a chip WNF101 (see picture).
I bought it from Fastech, but what is WNF101 ?
Thanks if you have some informations.
see http://onebus.fr/img/chip%20du%20module%20hm-16.jpg
Yves
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
Kindly check with the HM-16 manufacturer for info on this.
Thanks,
Hima
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Yes i did that.
The original manufacturer ot HM-16 is http://www.jnhuamao.cn and he use the good MCU CYBL10162
But i buyed several HM-16 (or copy ?) from Fastech and i have problem because this modules from Fastech havent not the good MCU !
Now i am talking with Fastech.
Best Regards
Yves Accard