[NAC1080]About One-step movement with external boostbuck circuit operation

Tip / Sign in to post questions, reply, level up, and achieve exciting badges. Know more

cross mob
u-s
Level 4
Level 4
Distributor - Macnica (Japan)
50 sign-ins 25 replies posted First like received

Hello, everone

 

I want to use the DEV_KIT_NAC1080 to rotate the motor 90 degrees forward and then 90 degrees reverse.
I referred to "One-step movement with external boostbuck circuit" in Table 1 of the user's manual "UM_2112_PL39_2202_112036" and confirmed the motor operation on the board.
https://www.infineon.com/dgdl/Infineon-NFC_actuation_sensing_IC_NAC1080_development_kit-UserManual-v...

In my confirmation, I could not confirm the expected operation of the motor (90° forward rotation and then 90° reverse rotation).

Could you tell me how to use the DEV_KIT_NAC1080 to make the motor rotate 90° forward rotation and then 90° reverse rotation?

PS.
My Evaluation board configuration as follows :
JP4 : OFF
JP5 : 2-3ON
JP6 : OFF
JP7 : ON
JP13 : ON
JP14 : ON

Best Regards
u-s

0 Likes
1 Solution
Takashi_O
Moderator
Moderator
Moderator
10 likes received 250 sign-ins 250 replies posted

@u-s -san,

Yes, your jumper settings are correct as described at "Evaluation board configuration" in Table 1.

Thanks,

View solution in original post

0 Likes
7 Replies
Takashi_O
Moderator
Moderator
Moderator
10 likes received 250 sign-ins 250 replies posted

@u-s -san,

Thank you for evaluating our new innovative device and posting your question on our forum.

If you want to evaluate the operation, "One-step movement with external boostbuck circuit" described in "Use of the evaluation kit in passive mode", FW update is needed as described there.

Please download "Infineon NAC1080 Firmware Sample: Boost-Buck Test Firmware" in the product page and write the FW to the device through debagger.

For the HW setting with debagger, you can find the chapter, "11 Debugger connection", in the application note.

Let me know if you have any questions in the process of FW writing. 

Thanks,

0 Likes
u-s
Level 4
Level 4
Distributor - Macnica (Japan)
50 sign-ins 25 replies posted First like received

Hi, TakashiO-san

Thank you for your answer.

I will try write the "Infineon NAC1080 Firmware Sample: Boost-Buck Test Firmware" to DEV_KIT_NAC1080 kit.
Could you tell me following settings for DEV_KIT_NAC1080 Kit is correct?
JP4 : OFF
JP5 : 2-3ON
JP6 : OFF
JP7 : ON
JP13 : ON
JP14 : ON

Best Regards
u-s

 

0 Likes
Takashi_O
Moderator
Moderator
Moderator
10 likes received 250 sign-ins 250 replies posted

@u-s -san,

Yes, your jumper settings are correct as described at "Evaluation board configuration" in Table 1.

Thanks,

0 Likes
u-s
Level 4
Level 4
Distributor - Macnica (Japan)
50 sign-ins 25 replies posted First like received

Hi, TakashiO-san

Thank you for your answer.

I will try with this content.

Best Regards
u-s

0 Likes
Takashi_O
Moderator
Moderator
Moderator
10 likes received 250 sign-ins 250 replies posted

@u-s -san,

Do you have any additional questions?

If we do not receive any replies from you within two business days, we will assume that this inquiry has been resolved and let us close this thread.

Thanks,

0 Likes
u-s
Level 4
Level 4
Distributor - Macnica (Japan)
50 sign-ins 25 replies posted First like received

Hi, TakashiO-san

Thank you for your answer.
I have already solved this problem.
Please close this thread.

Best Regards
u-s

0 Likes
Takashi_O
Moderator
Moderator
Moderator
10 likes received 250 sign-ins 250 replies posted

@u-s -san,

Thanks for your quick comment on this and I understood that you solve the issue.
Please push "Accept as solution" when you think the issue is solved in next time.

Thanks,

0 Likes