Announcements

From sunburn to sun earn – we’ve got the power! Watch our #poweringgreen videos now.

Tip / Sign in to post questions, reply, level up, and achieve exciting badges. Know more

cross mob
DevendraKumar
Level 1
Level 1
5 questions asked 5 replies posted 10 sign-ins

 Motor Parameters. Speed Ramp Rate Open Loop Speed Ramp Rate Parking Time Low Speed Threshold Low Speed Current Limit   whether these parameters need to be filled in the motor configuration file?

0 Likes
1 Solution
Viswa
Moderator
Moderator
Moderator
10 likes received 50 solutions authored 100 replies posted

Hi @DevendraKumar ,

The details are required for the motor configuration to be complete in case of closed loop control of PMSM/BLDC motors.

For controlling Induction motor the essential parameters are PWM frequency, Number of motor poles and motor max RPM.This document explains about induction motor control Induction motor control by iMOTION™ .

Best Regards,

View solution in original post

0 Likes
11 Replies
Viswa
Moderator
Moderator
Moderator
10 likes received 50 solutions authored 100 replies posted

Hi @DevendraKumar ,

The details are required for the motor configuration to be complete in case of closed loop control of PMSM/BLDC motors.

For controlling Induction motor the essential parameters are PWM frequency, Number of motor poles and motor max RPM.This document explains about induction motor control Induction motor control by iMOTION™ .

Best Regards,

0 Likes
DevendraKumar
Level 1
Level 1
5 questions asked 5 replies posted 10 sign-ins

Can I run Induction motor in Reverse direction using Kit?

 

0 Likes
Viswa
Moderator
Moderator
Moderator
10 likes received 50 solutions authored 100 replies posted

Hi @DevendraKumar 

 

Yes it is possible, based on the direction input.

Section 2.2.1 provides more details on Reference generator block.

Please go through Section 2.1.8 in iMOTION™ Motion Control Engine 

for further details on using control input.

 

Best Regards,

0 Likes
DevendraKumar
Level 1
Level 1
5 questions asked 5 replies posted 10 sign-ins

Hello Vishwa,

Can you please help to set Motor protection features in the Tool .

DevendraKumar_0-1676453684810.png

Please suggest how I can Enable Motor Protection features in the tool and see the SW Faults 

 

Thanks & Regards

Devendra

 

0 Likes
Krupashankar
Moderator
Moderator
Moderator
500 replies posted 50 likes received 25 likes received

Hi @DevendraKumar,

Motor fault protection can be enabled from MCE Wizard Ques 68 to Ques 74 or It can be enabled from MCE designer by writing corresponding values to each register mentioned below.

Krupashankar_0-1676459268553.png

For more details please refer to section 3.2.8 Protection Register Group of iMOTION™ Motion Control Engine Software Reference Manual

 

Thanks,

Krupashankar

 

0 Likes
DevendraKumar
Level 1
Level 1
5 questions asked 5 replies posted 10 sign-ins

Hi Krupa Shankar,

Is there any motor protection feature related to Phase reverse.

 

Thanks & Regards

Devendra Kumar 

0 Likes
Viswa
Moderator
Moderator
Moderator
10 likes received 50 solutions authored 100 replies posted

Hi @DevendraKumar 

There is no protection for phase reversal.

It has to be detected based on the application.

Best Regards

0 Likes
DevendraKumar
Level 1
Level 1
5 questions asked 5 replies posted 10 sign-ins

I have tested this but Motor Runs in Anticlock wise, I think If someone reverse phase then Motor Should be stopped. Is there any this type of Protection in this VFD kit ?

0 Likes
Viswa
Moderator
Moderator
Moderator
10 likes received 50 solutions authored 100 replies posted

Hi @DevendraKumar 

 

Based on the direction of rotation we should observe if either current or speed is higher or lower in one direction when compared to other and implement the solution as desired.

Best Regards

0 Likes
DevendraKumar
Level 1
Level 1
5 questions asked 5 replies posted 10 sign-ins

Hi Vishwa,

How to set Phase loss detection in the MCE designer tool and how I can see this in log.

Please help me.

Thanks & Regards

Devendra

0 Likes
Viswa
Moderator
Moderator
Moderator
10 likes received 50 solutions authored 100 replies posted

Hi @DevendraKumar 

 

Please check Section 2.1.16.6 Phase Loss Protection in software reference manual.

Viswa_0-1676883786718.png

 

Best Regards

0 Likes