I have taken the capsense csd tuning example for cy8ckit-149 devkit, i have connected the dev-kit to the tuner application by external miniprog4 programmer or debugger I2C communication.
In the sensor data I was getting maximum peaks in the sensor data section in the graph view. the maximum count value im getting on the sensor plot section is 65535 which i think it is a false value, only for a couple of seconds im getting the proper raw count as 1750 like that(csd is configured as 11 bit resolution).
And also after few seconds the communication with the board in the tuner application like exception happened. can you please let me know how can I solve this .Show Less
I have psoc 4100s plus. And I want to communicate with SHT20 temperature and humidity sensor and read the data. But I could not. I could not find the correct communication and reading addresses. Can you help me ?
I share the images of the products here.
I have purchased TC387QP board, when I plug this board there is default demo code is running [which I can see on TFT screen]. where I can find source file of this demo code ?
Thank you for help in Advance.Show Less
I'm trying to automate the programming of a CY8C3445AXI-104 device using the ppcli application, the problem I have is that I cannot find the ppcli command that will write the data to the PSoC from a hex file that has been read in. The following lines of code appear to work, but I'm at a loss as to what commands are used to program and verify the Hex file.
OpenPort MiniProg3/1636BB000190 .
I assume that the commands would be "PSoC3_ProgramRowFromHex" and "PSoC3_VerifyRowFromHex", but need further information on how to use these commands.
Am I also correct in thinking that the script would be completed with the following:
hi，we have encountered the click noise issue when press power off key to power off the unit in standby mode (no audio played this time), the irs2092 circuit is same as application note description. from the application note we know this chip have the click noise elimination function when power off, please advice why still occur the pop noise from speaker output of Tweeter, thanks.
Hello all, I am working on FX3 while interfacing a camera sensor with it. I need to debug and as mentioned that there are some ways to do so using segger debugger. I want to connect it on board. What pins I need to use to connect the segger JTAG (2*10 pins connector).
Dear Sirs and Madams,
We started using Modus Tool Box (MTB).
I would like to use XMC1100, however I can't find the BSP of "KIT_XMC_2GO_XMC1100_V1"
I found a similar question in this community.
From the answer to that question, I understand that I need to create a custom BSP from "xxxx-GENERIC".
Therefore, I created a new project from "XMC-GENERIC".
I have created a project for XMC1400-Q064x0200, However, the change to the XMC1100 implemented in the demo kit cannot be done well.
I've also confirm for MTB user manual, but don't have any documentation with more details on device changes?
Or are there any plans to release the BSP of "KIT_XMC_2GO_XMC1100_V1"?
KIT_XMC_2GO_XMC1100_V1 demo kit URL
Environment and SDK information:
WICED version: 6.4
Wi-Fi Module: Murata Type1GC
Wi-Fi connection(to wireless LAN AP) is lost immediately after 11 hours past with WPA3-SAE.
We think it was caused due to Wi-Fi module is down. It's not disconnected by wireless AP.
And we have already tried other wireless LAN AP from several vendors, and we confirmed that the same issue was reproduced in every case.
However, if we choose WPA2-PSK, the issue doesn't happen. Wi-Fi connection is still alive after 11 hours past.
Do you have any solutions to this issue?Show Less
I am using the FX3 Superspeed explorer kit and I want to use it with a camera module. I need to reset the image sensor and for that purpose i want use the GPIO 33. But i am not able to select pins over 27 with the GPIF designer. I am not able to remove the default reset pin from gpif designer because the state machine uses it. Can i somehow overcome this problem?Show Less