Welcome to the Infineon Developer Community

label showing "sample" on the label. not sure if it will impact the production use or not. Since we're afraid that it is trial run parts. and technical spec is not the same as normal production parts. 

Please help confirm. thanks!

Can you clarify what is the most recent SDK Available for the CYW20719B2 chip?  From within Modus ToolBox it seems that V3.3.0 is the most recent.  Previously there was a V4.0 available (and I have release notes for it) but it no longer seems to be an option.   I see references to a V4.2.0 on this forum, but cannot find any information about it.  Is 4.2.0 applicable to the 20719 chip?  

Hi,

I want to convert my CYBT-4803056 module to EZ-serial but firmware as per knowledge base I downloaded the WICED_MOD_Prog_v1.5.19.102.zip but when opened I found it did not support CYBT-483056 board.

Please guide me how I can program this in CYBT-483056 board.

Thanks in advance.

Prasad

As noted in another recent question:  https://community.infineon.com/t5/Bluetooth-SDK/a2dp-sink-cant-t-connect-to-20719-a2dp-source/td-p/330401 the Watch Example provided as reference code for A2DP implementation seems to have problems with the connection sequence, and it appears that the code does not actually perform to the Bluetooth Specification.  Can you explain the apparent deficiencies or provide examples of compliant code?  

As noted in the referenced post above, the connection sequence always seems to  fail for a previously paired device.  And we do not seem to be able to get SBC output to play on Airpods at all.

Hello.
I have  one question.

Used Evkit   CYTVII-B-E-1M-SK. 

Set P6.3 to Pwm Pulse Output. 
I want to interrupt and enter to Pwm_out_isr_handler() by PWM signal output. 

When I excuted attached FW(main_cm4.zip),
PWM (P6.3) is output at 1280us period like below  yellow wave in oscilloscope picture. 

At this time, when I applied GPIO Flag (P11.1) to Pwm_out_isr_handler(),
it was interrupted every 1.54u/2 like below  green wave in oscilloscope picture. 

How can I interrupt by PWM (P6.3) signal output (every 1280us)?

Green Color : Toggle_FLAG1(P11.1) 
Yellow Color: PWM Output (P6.3) 

Hi,

We performed a circuit setup with the processor we have (CY8C5867LTI-LP028). There are components TIA, DVDAC, VDAC, SAR ADC, OPAMP(3 pieces) and UART in the circuit. When we run it in "Release" mode, the processor constantly resets itself. When we look at the "Debug" mode, after opening TIA, DVDAC, VDAC, OPAMP(3 pieces) and UART, a debug error is given when opening DelSig ADC. How can I run the processor correctly?

Note: The processor is working properly when DelSig ADC is turned off. I can use DelSig ADC when used alone.

Best wishes.

Respected fellow designers,

I am trying to interface HC-05 bluetooth module with XMC4700 relax kit.

I have the TX and RX running in arduino IDE without any issues.

However, I wish to replicate the same using Modus tool box.

I am able to transmit through the HC-05 module and see the output in my mobile.

However, I am unable to get the receiver working.

I have tried using RX FIFO but could not get any output.

I have shared my project.

Kindly suggest  some method to get  TX and RX working through modus toolbox.

Thank you

HI, I use a TLE9862 device have the issue that PWM and LIN is not working after powering the target hardware. If I  pull the RESET pin low after power on (in order to trigger another reset), PWM and LIN is working.  Has anybody observed a similar behavior and can help me with that? Thanks in advance!

Dear all, 

For one on my projects im working on, i want to know how it is possible to lock/unlock the JTAG port for the  CYT2B75BADQ0AZEGST microcontroller ? 

Please, is it possible to have some ideas ? It will be helpful

Thanks, 

Abbass